Phone · Motorola · Moto Edge Plus 2022
Motorola Moto Edge Plus 2022 Logic Board Repair
Logic Board Repair guide for the Motorola Moto Edge Plus 2022
Before you begin
Tools
- Heat gun or hair dryer
- Precision screwdriver set (Phillips #000)
- Plastic prying tools
- Suction cup tool
- Tweezers
- Spudger tool
- SIM eject tool
- Anti-static wrist strap
Parts / materials
- Isopropyl alcohol (91%+)
- Replacement rear cover adhesive
- Replacement logic board
- Lint-free microfiber cloth
Safety
- Wear protective eye gear while heating and prying glass panels.
- Disconnect the battery first before touching internal components to prevent electrical shorts.
- Wear an anti-static wrist strap to avoid ESD damage to sensitive board components.
Overview
Step-by-step
- 1
Power Off and Eject SIM Tray
1 minTurn off your Motorola Moto Edge Plus 2022 completely. Insert a SIM eject tool into the hole at the bottom of the phone to remove the SIM tray.
- 2
Heat the Rear Glass Cover
3 minApply heat to the edges of the rear glass panel for 2 to 3 minutes using a heat gun to soften the underlying adhesive.
- 3
Attach Suction Cup
2 minPress a suction cup near the bottom edge of the rear glass and gently pull upward to create a slight gap.
- 4
Slice Rear Panel Adhesive
5 minInsert a plastic prying pick into the gap and slowly slide it along the perimeter to cut through the adhesive.
- 5
Remove the Rear Glass Cover
2 minLift the rear glass panel off the frame carefully and set it aside on a clean surface.
- 6
Unscrew Top Midframe Shield
4 minRemove the Phillips #000 screws securing the top protective cover and wireless charging coil assembly.
- 7
Remove Top Midframe Shield
2 minUse a spudger to gently pry up and lift out the top plastic midframe shield along with the coil.
- 8
Disconnect the Battery Cable
1 minPry the battery press connector straight up off the logic board using a plastic spudger to prevent short circuits.
- 9
Disconnect Display and Interconnect Cables
3 minDisconnect the main display flex cable and the lower sub-board interconnect cables from the board using a spudger.
- 10
Disconnect Coaxial Antenna Cables
2 minUnplug the antenna coaxial cables from the logic board using fine tweezers by gently prying near their heads.
- 11
Disconnect the Front Camera
2 minDetach the selfie camera flex cable connector from the top section of the logic board.
- 12
Remove Logic Board Retaining Screws
2 minUnscrew any remaining Phillips screws securing the logic board to the internal frame.
- 13
Extract the Logic Board
3 minCarefully pry up the edges of the logic board and lift it out of the chassis, avoiding any snagged cables.
- 14
Transfer Rear Camera Modules
4 minDisconnect and transfer the rear camera sensor assembly from the original logic board to the replacement board.
- 15
Position New Logic Board
3 minAlign the replacement logic board over the frame cutouts and lower it gently into position.
- 16
Reconnect All Board Connectors
4 minSnap the front camera, display flex, interconnect cables, and antenna cables back onto the logic board.
- 17
Reconnect Battery and Secure Shield
4 minReconnect the battery press connector, reattach the upper midframe shield, and reinstall all Phillips screws.
- 18
Reseal the Rear Glass
4 minApply new custom adhesive strips to the perimeter of the phone frame and firmly press the rear glass into place.
After your Motorola Moto Edge Plus 2022 logic board repair
Power the Moto Edge Plus 2022 back on and test the logic board repair function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Motorola Moto Edge Plus 2022 job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Prefer a professional repair?
Book Motorola Moto Edge Plus 2022 logic board repair at LML Repair in Seattle — same-day options available.
