Phone · Motorola · Moto Edge 60 Pro
Motorola Moto Edge 60 Pro Speaker Repair
Speaker Repair guide for the Motorola Moto Edge 60 Pro
Before you begin
Tools
- Precision Phillips PH00 screwdriver
- Plastic opening picks
- Suction cup
- Heat gun or iOpener
- Plastic spudger
- Tweezers
- SIM eject tool
- Anti-static wrist strap
Parts / materials
- Replacement Moto Edge 60 Pro loudspeaker module
- Pre-cut back cover adhesive tape
- High-purity isopropyl alcohol (90%+)
- Lint-free cleaning wipes
Safety
- Wear eye protection when applying heat to glass panels to guard against splintering.
- Use an anti-static wrist strap to protect sensitive internal components from electrostatic discharge.
- Do not heat the rear panel above 80°C (176°F) to avoid damaging the internal lithium-ion battery.
Overview
Step-by-step
- 1
Power Off the Device
1 minPress and hold the Power button, then select Power Off on the screen. Ensure the phone is completely powered down before starting.
- 2
Eject the SIM Card Tray
1 minInsert a SIM eject tool into the small pinhole near the bottom edge of the frame. Push firmly until the tray pops out, then remove it.
- 3
Heat the Back Glass Panel
3 minApply heat from a heat gun or heated pad around all edges of the rear panel for 2 to 3 minutes to soften the adhesive.
- 4
Attach Suction Cup and Pry Edge
2 minPlace a suction cup near the bottom edge of the back panel and pull up gently to create a small gap. Insert a plastic opening pick into the gap.
- 5
Slice the Rear Adhesive
4 minSlide the plastic pick around the perimeter of the phone to cut through the adhesive. Reapply heat if the pick encounters heavy resistance.
- 6
Remove the Back Cover
2 minGently lift the back cover away from the chassis. Set the panel aside on a clean, soft surface.
- 7
Unscrew the Speaker Cover
3 minUse a precision Phillips screwdriver to remove the screws holding down the lower speaker enclosure assembly.
- 8
Pry Up the Speaker Housing
2 minInsert the edge of a plastic spudger beneath the speaker module notch and gently pry it upward to unclip it.
- 9
Remove the Faulty Loudspeaker
1 minLift the loudspeaker module out from the lower frame. Inspect the cavity for any debris or leftover speaker mesh adhesive.
- 10
Install the New Loudspeaker
2 minLower the replacement loudspeaker module into the chassis, ensuring the golden contact pins align with the daughterboard pads.
- 11
Snap the Speaker Cover in Place
2 minAlign the speaker cover over the bottom assembly and press down until you hear the plastic clips engage firmly.
- 12
Secure the Speaker Cover Screws
3 minReinstall and tighten the Phillips screws in a crisscross pattern until snug. Avoid overtightening.
- 13
Clean Frame and Apply Adhesive
4 minClean remaining glue from the frame edges using isopropyl alcohol, then apply fresh pre-cut adhesive strips to the perimeter.
- 14
Reattach the Back Cover
2 minAlign the back panel with the phone frame and press firmly along all edges to ensure a tight, secure seal.
After your Motorola Moto Edge 60 Pro speaker repair
Power the Moto Edge 60 Pro back on and test the speaker repair function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Motorola Moto Edge 60 Pro job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Prefer a professional repair?
Book Motorola Moto Edge 60 Pro speaker repair at LML Repair in Seattle — same-day options available.
