Phone · Motorola · Moto Edge 50 Fusion 5G
Motorola Moto Edge 50 Fusion 5G Battery Replacement
Battery Replacement guide for the Motorola Moto Edge 50 Fusion 5G
Before you begin
Tools
- Heat gun or hair dryer
- Suction cup tool
- Opening picks
- Phillips #000 screwdriver
- Spudger tool
- Tweezers
- Plastic prying tools
Parts / materials
- Replacement Moto Edge 50 Fusion 5G battery
- Battery adhesive removal strips
- Isopropyl alcohol (90%+)
- Rear cover adhesive seal
Safety
- Discharge the battery below 25% before starting to reduce the risk of fire.
- Wear safety glasses to protect your eyes from possible glass fragments.
- Never use sharp metal tools directly against the battery to prevent punctures.
Overview
Step-by-step
- 1
Power Off the Device
1 minPress and hold the power button, then tap Power Off on the screen. Disconnect any connected USB cables.
- 2
Heat the Rear Panel
2 minApply heat to the edges of the rear panel using a heat gun or hair dryer for about two minutes to soften the adhesive.
- 3
Attach the Suction Cup
1 minPress a suction cup firmly onto the lower section of the rear cover near the bottom edge.
- 4
Create an Entry Gap
2 minPull up on the suction cup and insert a thin opening pick into the gap created between the frame and rear panel.
- 5
Slice the Rear Adhesive
4 minSlide the opening pick around all four edges of the device to cut through the perimeter adhesive.
- 6
Lift Away the Rear Cover
1 minGently lift the back cover off the phone frame and place it safely on your clean workspace.
- 7
Unscrew the Upper Bracket
3 minUse a Phillips #000 screwdriver to remove the screws securing the upper motherboard cover bracket.
- 8
Remove the Motherboard Bracket
2 minInsert a spudger under the edge of the upper plastic cover and lift it away from the chassis.
- 9
Disconnect the Battery Cable
1 minPry the battery press connector straight up from its motherboard socket using the flat end of a plastic spudger.
- 10
Unscrew the Loudspeaker Assembly
2 minRemove the Phillips screws holding the lower speaker enclosure to the bottom of the phone frame.
- 11
Remove the Loudspeaker Module
2 minPry up the speaker module using a spudger to clear access to the lower battery pull tabs.
- 12
Apply Isopropyl Alcohol
2 minDispense a few drops of high-concentration isopropyl alcohol along the battery edges to dissolve stubborn glue.
- 13
Pull the Adhesive Strips
4 minGrasp the exposed adhesive pull tabs with tweezers and pull them out slowly at a low angle.
- 14
Pry Out the Battery
3 minGently slide a plastic prying tool under the battery to lift it out of the recess.
- 15
Clean the Frame Well
2 minWipe away leftover adhesive residue inside the frame using isopropyl alcohol and a lint-free cloth.
- 16
Install Replacement Adhesive
2 minApply new battery adhesive strips into the housing, ensuring correct orientation before pressing down.
- 17
Seat the New Battery
2 minAlign the replacement battery into the frame well and press firmly into place.
After your Motorola Moto Edge 50 Fusion 5G battery replacement
Power the Moto Edge 50 Fusion 5G back on and test the battery replacement function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Motorola Moto Edge 50 Fusion 5G job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Prefer a professional repair?
Book Motorola Moto Edge 50 Fusion 5G battery replacement at LML Repair in Seattle — same-day options available.
