Phone · Motorola · Moto Edge 20 Fusion
Motorola Moto Edge 20 Fusion Speaker Repair
Speaker Repair guide for the Motorola Moto Edge 20 Fusion
Before you begin
Tools
- Phillips #00 screwdriver
- Plastic opening tools
- Plastic opening picks
- Suction cup
- Tweezers
- Heat gun or hair dryer
- Anti-static wrist strap
Parts / materials
- Replacement loudspeaker module
- Rear cover adhesive strips
- 99% Isopropyl alcohol
Safety
- Always power down the device completely before performing internal repairs.
- Wear safety glasses to protect against potential glass or plastic fragments.
- Do not apply excess heat directly over the internal battery area.
Overview
Step-by-step
- 1
Power Off and Remove SIM Tray
1 minPower off the Moto Edge 20 Fusion completely. Insert a SIM eject tool into the hole on the left edge and remove the SIM tray.
- 2
Heat the Rear Panel
2 minApply heat around the edges of the back cover for two minutes using a heat gun or hairdryer to soften the perimeter adhesive.
- 3
Attach the Suction Cup
1 minPress a suction cup firmly onto the lower section of the rear panel and gently pull upward to create a small gap.
- 4
Insert an Opening Pick
1 minSlide a plastic opening pick into the gap between the rear cover and the outer frame.
- 5
Slice the Rear Adhesive
3 minMove the pick along all sides of the phone to cut through the sticky seal holding the rear cover.
- 6
Lift the Back Cover
2 minCarefully lift the back cover from the frame, taking care not to strain the fingerprint sensor ribbon cable.
- 7
Disconnect the Fingerprint Cable
2 minUse a spudger to gently pop the fingerprint reader flex cable off its connector on the motherboard.
- 8
Unscrew the Loudspeaker Assembly
3 minRemove the Phillips #00 screws securing the plastic loudspeaker housing at the bottom of the phone.
- 9
Pry Up the Loudspeaker Module
2 minInsert the flat tip of a spudger beneath the edge of the loudspeaker assembly and pry it upward.
- 10
Remove the Faulty Loudspeaker
1 minLift the original loudspeaker module out of the chassis recess and set it aside.
- 11
Clean Old Frame Adhesive
2 minClean remaining glue or adhesive residue off the frame perimeter using high-percentage isopropyl alcohol.
- 12
Insert the New Loudspeaker
2 minAlign the replacement loudspeaker module with the lower housing slot and press it down into position.
- 13
Secure the Loudspeaker Screws
3 minReinstall and tighten all Phillips #00 screws to hold the loudspeaker assembly firmly in place.
- 14
Reconnect the Fingerprint Cable
2 minAlign the fingerprint sensor press connector over its motherboard socket and press down until it snaps in place.
- 15
Apply New Rear Adhesive
3 minLay fresh pre-cut adhesive strips along the perimeter frame where the back cover rests.
- 16
Seal the Rear Panel
2 minAlign the back panel with the phone chassis and press evenly around all edges to set the seal.
After your Motorola Moto Edge 20 Fusion speaker repair
Power the Moto Edge 20 Fusion back on and test the speaker repair function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Motorola Moto Edge 20 Fusion job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Prefer a professional repair?
Book Motorola Moto Edge 20 Fusion speaker repair at LML Repair in Seattle — same-day options available.
