Phone · Motorola · Moto Edge 20 Fusion
Motorola Moto Edge 20 Fusion Charging Port Repair
Charging Port Repair guide for the Motorola Moto Edge 20 Fusion
Before you begin
Tools
- Precision screwdriver set
- Plastic opening tools
- Tweezers
- Heat gun or iOpener
- Suction handle
- SIM card eject tool
- Plastic spudger
Parts / materials
- Replacement charging port board
- Pre-cut back cover adhesive
- 90%+ isopropyl alcohol
- Microfiber cleaning cloth
Safety
- Wear safety glasses to protect your eyes when applying heat and handling glass or plastic components.
- Always disconnect the battery connector before handling internal electronics to avoid short circuits.
- Do not puncture or crush the lithium-ion battery during disassembly.
Overview
Step-by-step
- 1
Power Down Device
1 minPress and hold the power button, then tap Power Off to completely turn off the device.
- 2
Eject SIM Tray
1 minInsert a SIM eject pin into the small hole on the side frame and push gently to remove the SIM tray.
- 3
Heat Back Cover
2 minApply heat around the outer edges of the rear panel for two minutes using a heat gun or iOpener to soften the perimeter adhesive.
- 4
Attach Suction Cup
1 minPlace a suction cup onto the lower portion of the rear panel and pull up gently to create a small gap.
- 5
Slice Rear Adhesive
4 minInsert an opening pick into the gap and slowly slide it along all four edges to cut through the glue.
- 6
Remove Back Cover
1 minCarefully lift the rear panel away from the frame and place it off to the side.
- 7
Remove Loudspeaker Screws
2 minUnscrew the seven Phillips #00 screws holding down the lower loudspeaker cover assembly.
- 8
Remove Loudspeaker Assembly
1 minInsert a plastic spudger under the edge of the loudspeaker bracket and lift it out of the phone.
- 9
Disconnect Battery Cable
1 minPry up the main battery connector from the motherboard to cut power to the device during the repair.
- 10
Disconnect Interconnect Cable
1 minUse a plastic spudger to pop off the bottom flex cable connector from the charging port board.
- 11
Disconnect Coaxial Antenna Cable
1 minGently lift the antenna connector off its socket on the charging port board using precision tweezers.
- 12
Unfasten Charging Board Screw
1 minRemove the single Phillips #00 screw holding the charging port sub-board to the frame.
- 13
Pry Up Charging Board
2 minInsert a flat plastic tool under the charging board and pry it up from the chassis glue.
- 14
Install New Charging Board
1 minAlign the replacement charging port board in the bottom cavity and press it gently into place.
- 15
Secure Charging Board Screw
1 minReinstall and tighten the single Phillips #00 screw securing the sub-board to the chassis.
- 16
Attach Antenna Cable
2 minUse tweezers to position the coaxial antenna cable head and press down until it snaps onto the terminal.
- 17
Reconnect Interconnect Cable
1 minAlign the main flex ribbon cable over its sub-board socket and press firmly until it clicks.
- 18
Reconnect Battery Cable
1 minSnap the battery press connector back onto the motherboard terminal.
- 19
Reinstall Loudspeaker Assembly
1 minPosition the loudspeaker bracket over the bottom section and press it flat against the frame.
- 20
Secure Loudspeaker Screws
2 minDrive the seven Phillips #00 screws back into the loudspeaker cover until snug.
- 21
Apply Rear Cover Adhesive
3 minApply new double-sided adhesive strips along the edges of the phone frame after cleaning residual glue with isopropyl alcohol.
- 22
Seal Rear Cover
2 minAlign the back cover with the frame and press firmly along the perimeter to secure the seal.
- 23
Reinsert SIM Tray
1 minPush the SIM card tray back into its slot until it rests flush with the outer frame.
After your Motorola Moto Edge 20 Fusion charging port repair
Power the Moto Edge 20 Fusion back on and test the charging port repair function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Motorola Moto Edge 20 Fusion job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Prefer a professional repair?
Book Motorola Moto Edge 20 Fusion charging port repair at LML Repair in Seattle — same-day options available.
