Phone · Samsung · Galaxy Z Fold 6 5G
Samsung Galaxy Z Fold 6 5G Charging Port Repair
Charging Port Repair guide for the Samsung Galaxy Z Fold 6 5G
Before you begin
Tools
- Heat gun or hair dryer
- Suction cup tool
- Plastic prying tools
- Precision screwdriver set (Phillips #000)
- Spudger tool
- Tweezers
- SIM eject tool
Parts / materials
- Replacement Samsung Galaxy Z Fold 6 charging port daughterboard
- Pre-cut rear back glass adhesive strips
- Isopropyl alcohol (99%)
Safety
- Wear safety glasses to protect your eyes from potential glass shards during rear panel removal.
- Work in a well-ventilated area away from flammable materials when using heat tools.
- Disconnect the battery press connector immediately after opening to prevent electrical shorts.
Overview
Step-by-step
- 1
Power Down the Galaxy Z Fold 6
1 minTurn off the phone completely before starting disassembly. Disconnect all external cables.
- 2
Eject the SIM Card Tray
1 minInsert a SIM ejector tool into the hole beside the SIM tray to release it. Pull the tray out and set it aside.
- 3
Heat the Outer Rear Glass
3 minApply heat using a heat gun or hair dryer around the edges of the outer rear glass panel for 2 to 3 minutes.
- 4
Attach Suction Cup
1 minPress a suction cup firmly onto the lower portion of the heated outer back glass near the edge.
- 5
Insert Opening Pick
2 minPull up gently on the suction cup to create a small gap between the glass and the frame, then insert a plastic pick.
- 6
Slice Rear Panel Adhesive
4 minSlide the plastic pick along all four sides of the rear glass panel to slice through the factory adhesive.
- 7
Remove Back Glass Panel
2 minCarefully lift the outer rear glass panel off the chassis and set it face-up on a clean surface.
- 8
Unscrew Wireless Coil Bracket
3 minRemove the Phillips #000 screws securing the wireless charging coil shield and upper midframe cover.
- 9
Disconnect Wireless Charging Assembly
2 minUse a spudger to detach the wireless charging coil connector, then peel off and remove the wireless coil assembly.
- 10
Unscrew Loudspeaker Module
3 minRemove the Phillips #000 screws holding down the lower loudspeaker module that covers the sub-board.
- 11
Remove Loudspeaker Module
2 minPry up the lower speaker module using a plastic spudger and lift it out of the lower chassis.
- 12
Disconnect Battery Flex Cable
1 minGently pry up the battery press connector from the motherboard with a plastic spudger to cut power.
- 13
Disconnect Interconnect Flex Cables
2 minDisconnect the main interconnect flex cables connected to the charging port daughterboard using your spudger.
- 14
Disconnect Antenna Cables
2 minUse fine tweezers to carefully unclip the coaxial antenna cables from the charging port sub-board.
- 15
Unscrew Charging Port Board
2 minRemove the Phillips #000 screws holding the charging port daughterboard to the lower frame.
- 16
Pry Up Old Charging Port
2 minInsert a plastic spudger underneath the USB-C daughterboard and gently lift it out of its housing recess.
- 17
Install New Charging Port Board
2 minPosition the replacement USB-C daughterboard into the lower frame recess and press it down flush.
- 18
Secure Daughterboard Screws
2 minReinstall and tighten the Phillips #000 screws to fasten the new charging port sub-board in place.
- 19
Reconnect Antenna and Flex Cables
3 minSnap the coaxial antenna connectors and main interconnect flex cables back onto the sub-board header sockets.
- 20
Reconnect Battery and Test Port
3 minPlug the battery connector back in, temporarily attach a charging cable, and confirm charging works.
- 21
Reinstall Speaker and Wireless Coil
4 minPlace the loudspeaker module and wireless coil pad back in position, then reinstall all Phillips #000 screws.
- 22
Reseal Rear Glass Panel
3 minApply pre-cut replacement adhesive to the housing perimeter and press the back glass firmly into place.
After your Samsung Galaxy Z Fold 6 5G charging port repair
Power the Galaxy Z Fold 6 5G back on and test the charging port repair function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Samsung Galaxy Z Fold 6 5G job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Prefer a professional repair?
Book Samsung Galaxy Z Fold 6 5G charging port repair at LML Repair in Seattle — same-day options available.
