Phone · Motorola · Moto G Stylus 5G 2023
Motorola Moto G Stylus 5G 2023 Logic Board Repair
Logic Board Repair guide for the Motorola Moto G Stylus 5G 2023
Before you begin
Tools
- Heat gun or hair dryer
- Suction cup tool
- Plastic prying tools
- Precision screwdriver set (Phillips #00)
- Tweezers
- Spudger tool
- SIM eject tool
- Anti-static wrist strap
Parts / materials
- Pre-cut back cover adhesive
- Isopropyl alcohol (99%)
- Lint-free microfiber cloth
Safety
- Always disconnect the battery connector before handling or removing internal components.
- Wear eye protection when heating and prying adhesives to protect against sudden snaps or glass shards.
- Wear an anti-static wrist strap to avoid damaging delicate integrated circuits on the logic board.
Overview
Step-by-step
- 1
Eject SIM tray and stylus
1 minInsert a SIM eject tool into the tray hole to pop out the SIM tray, then press and remove the built-in stylus from its slot.
- 2
Heat the back panel
2 minApply a heat gun or hair dryer around the outer edges of the rear cover for 2 minutes to soften the adhesive seal.
- 3
Slice the perimeter adhesive
4 minAttach a suction cup near the bottom edge, pull gently to create a gap, and insert a plastic opening pick. Slide the pick along all edges to slice through the adhesive.
- 4
Remove the back panel
2 minCarefully lift the rear panel off the housing. Clean away any residual adhesive tape from the frame using tweezers.
- 5
Unscrew the upper midframe
3 minUse a Phillips #00 screwdriver to remove the screws securing the upper plastic motherboard cover.
- 6
Remove the upper midframe
2 minInsert a spudger under the edge of the upper midframe cover and gently lever it up to unclip and remove it.
- 7
Disconnect the battery cable
1 minUse the flat end of a plastic spudger to pry the battery press-connector straight up from its motherboard socket.
- 8
Disconnect the main flex cable
1 minPry up the main interconnect flex cable connector from the bottom section of the logic board.
- 9
Disconnect the display cable
1 minUse your plastic spudger to pop the display flex cable connector off the logic board.
- 10
Disconnect the antenna cables
2 minUse precision tweezers to gently pry the white and black coaxial antenna heads straight up from the board.
- 11
Disconnect the camera modules
2 minUnclip the press-connectors for the rear camera sensors and the front-facing selfie camera.
- 12
Remove the board retention screw
1 minLocate and remove the single Phillips #00 screw securing the top corner of the logic board to the frame.
- 13
Pry up the logic board
2 minInsert a spudger under the bottom edge of the logic board and gently lever it upward out of its recessed housing.
- 14
Lift out the logic board
1 minGrasp the logic board by its edges and lift it completely out of the phone frame, ensuring no cables catch on the board.
After your Motorola Moto G Stylus 5G 2023 logic board repair
Power the Moto G Stylus 5G 2023 back on and test the logic board repair function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Motorola Moto G Stylus 5G 2023 job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Keep learning
Explore more Motorola Moto G Stylus 5G 2023 repair context in the encyclopedia, or open related DIY guides.
