Console · Nintendo · Wii U Gamepad
Nintendo Wii U Gamepad HDMI Port Repair
HDMI Port Repair guide for the Nintendo Wii U Gamepad
Before you begin
Tools
- Phillips #0 screwdriver
- Tri-point Y0 screwdriver
- Tweezers
- Plastic spudger
- Hot air rework station
- Soldering iron
- Desoldering wick
- Magnifying glass or headlamp
Parts / materials
- Replacement connector port
- Soldering flux
- Lead-free solder wire
- 99% Isopropyl alcohol
- Cotton swabs
Safety
- Wear safety glasses while soldering and using hot air tools.
- Work in a well-ventilated space to avoid inhaling flux fumes.
- Ensure the battery is completely disconnected before starting board-level work.
Overview
Step-by-step
- 1
Remove battery cover screw
1 minUse a Phillips #0 screwdriver to loosen the captive screw on the battery compartment door on the back of the GamePad.
- 2
Remove battery door
1 minLift the plastic battery door away from the GamePad chassis and set it aside.
- 3
Disconnect battery pack
2 minUnplug the white battery connector from the circuit board and lift the battery out of the bay.
- 4
Peel off screw covers
2 minUse fine tweezers to remove the four rubber screw covers on the back panel to reveal hidden screws.
- 5
Remove rear housing screws
4 minRemove the ten Tri-point Y0 screws securing the rear case to the front assembly.
- 6
Separate housing halves
2 minGently lift the rear housing straight up, taking care not to strain the attached shoulder button cables.
- 7
Disconnect shoulder button cables
2 minUnplug the L and R button flex cable connectors from the mainboard using a plastic spudger.
- 8
Remove battery frame screws
3 minUnscrew the four Phillips #0 screws holding the internal plastic battery frame in place.
- 9
Lift out battery frame
1 minRemove the battery frame from the GamePad chassis to access the display and board connections.
- 10
Disconnect ribbon cables
3 minFlip up the ZIF retaining flaps and gently pull out the screen and digitizer ribbon cables with tweezers.
- 11
Remove mainboard screws
3 minRemove the six Phillips #0 screws securing the mainboard to the front housing.
- 12
Lift out mainboard
2 minCarefully lift the mainboard out of the front housing and place it on an anti-static work surface.
- 13
Apply liquid flux
2 minApply a liberal amount of liquid soldering flux across the connector's anchor pins and signal pads.
- 14
Desolder damaged port
5 minHeat the port mounting pins with a hot air rework station at 350°C until the solder melts, then lift the port off with tweezers.
- 15
Clean PCB pads
3 minUse desoldering wick and a soldering iron to clear residual solder from all copper pads on the mainboard.
- 16
Solder replacement port
8 minAlign the new port onto the pads, tack down the side anchor legs, and carefully solder each signal pin under magnification.
- 17
Clean flux residue
2 minScrub the soldered area with a cotton swab dipped in 99% isopropyl alcohol to remove leftover flux.
After your Nintendo Wii U Gamepad hdmi port repair
Power the Wii U Gamepad back on and test the hdmi port repair function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Nintendo Wii U Gamepad job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Keep learning
Explore more Nintendo Wii U Gamepad repair context in the encyclopedia, or open related DIY guides.
