Skip to main content
logo

Tablet · Microsoft · Surface Go

Microsoft Surface Go Charging Port Repair

Charging Port Repair guide for the Microsoft Surface Go

Moderate
~59 min
27 steps

Before you begin

Tools

  • Precision screwdriver set
  • Plastic opening tools
  • Plastic opening picks
  • Suction handle
  • Heat gun
  • Tweezers
  • Spudger

Parts / materials

  • Pre-cut display adhesive strips
  • Isopropyl alcohol (99%)
  • Lint-free microfiber cloth

Safety

  • Wear safety glasses to protect eyes from potential glass fragments while prying.
  • Disconnect the battery before servicing internal motherboards to avoid short-circuiting.
  • Wear an anti-static wrist strap to protect delicate electronics from electrostatic discharge.

Overview

# Microsoft Surface Go Charging Port Repair Repair Guide Action-specific charging port repair walkthrough for the Microsoft Surface Go. About 59 minutes across 27 steps. This DIY guide walks through charging port repair on the Microsoft Surface Go (Surface series tablet). Before you open the device, confirm the exact model number on the Microsoft settings screen or rear housing so your replacement part matches the Surface Go specifically—not a similar Surface sibling. Most DIY techs finish this Microsoft Surface Go charging port repair in about 59 minutes when parts and tools are ready. Difficulty is rated intermediate for this model. Recommended tools for this Microsoft Surface Go job: Precision screwdriver set, Plastic opening tools, Plastic opening picks, Suction handle, Heat gun, Tweezers, Spudger. Parts and supplies: Pre-cut display adhesive strips, Isopropyl alcohol (99%), Lint-free microfiber cloth. Power the Surface Go off completely, remove SIMs/SD cards if present, and work on a clean, well-lit surface with a magnetic mat for screws. If a step feels wrong for your Microsoft Surface Go, stop and compare the connector layout to the photos in this guide. When you prefer a same-day pro repair in Seattle instead, LML Repair can handle charging port repair for this model with tested parts and a workmanship warranty.

Step-by-step

  1. 1

    Power down the tablet

    1 min

    Turn off the Microsoft Surface Go completely and unplug all external cables.

  2. 2

    Warm display adhesive

    3 min

    Apply a heated pad or heat gun around the screen edges for two minutes to soften the strong adhesive.

  3. 3

    Attach suction handle

    1 min

    Press a suction cup onto the top-center edge of the glass screen to gain leverage.

  4. 4

    Create opening gap

    2 min

    Pull up firmly on the suction handle while inserting a thin opening pick between the glass and body frame.

  5. 5

    Slice top edge adhesive

    3 min

    Slide the plastic opening pick carefully along the top seam to cut through the display adhesive.

  6. 6

    Slice left edge adhesive

    3 min

    Work the pick down the left side edge, keeping the pick shallow to avoid damaging internal components.

  7. 7

    Slice right edge adhesive

    3 min

    Slide the pick along the right edge to separate the remaining adhesive bond.

  8. 8

    Slice bottom edge adhesive

    3 min

    Carefully slice along the bottom frame edge, taking extra care not to slide deeper than 3mm near display cables.

  9. 9

    Pivot display assembly

    2 min

    Gently lift the top edge of the glass, pivoting the screen open towards the bottom connector area.

  10. 10

    Unscrew display connector bracket

    2 min

    Remove the T3 Torx screws securing the metal shield over the display cable socket.

  11. 11

    Remove display bracket

    1 min

    Use tweezers to lift and remove the small metal shield covering the screen flex cable.

  12. 12

    Disconnect display flex cable

    1 min

    Pry the display connector straight up off the motherboard using a plastic spudger.

  13. 13

    Disconnect battery terminal

    2 min

    Pry up the battery contact flex connection on the motherboard to prevent electrical shorts during repair.

  14. 14

    Unscrew motherboard shield

    4 min

    Remove the T3 screws securing the central motherboard EMI shield.

  15. 15

    Remove motherboard shield

    2 min

    Carefully lift the metal motherboard cover off the board and set it aside.

  16. 16

    Unscrew charging port bracket

    3 min

    Remove the screws holding down the Surface Connect charging port assembly to the chassis.

  17. 17

    Disconnect charging port cable

    1 min

    Use the flat end of a spudger to disconnect the charging port ribbon cable from the motherboard.

  18. 18

    Remove defective charging port

    1 min

    Lift the damaged charging port assembly out of its slot in the magnesium case.

  19. 19

    Position replacement charging port

    2 min

    Place the new charging port module into the housing recess until properly aligned.

  20. 20

    Fasten charging port screws

    2 min

    Reinstall and tighten the screws to hold the replacement charging port securely in place.

  21. 21

    Connect charging port flex cable

    1 min

    Align and press the charging port ribbon connector straight down onto its motherboard socket.

  22. 22

    Reinstall motherboard shield

    3 min

    Set the motherboard EMI shield back in place and secure all retained screws.

  23. 23

    Reconnect battery terminal

    1 min

    Press the battery connector down onto the motherboard interface until fully seated.

  24. 24

    Connect display flex cable

    2 min

    Snap the main display flex cable back onto its motherboard socket.

  25. 25

    Reinstall display connector shield

    2 min

    Place the metal shield over the display cable connector and secure its T3 Torx screws.

  26. 26

    Apply new frame adhesive

    5 min

    Clean off old glue residue with isopropyl alcohol and apply pre-cut adhesive strips around the rim.

  27. 27

    Seal display assembly

    3 min

    Align the screen with the housing edges and press firmly around the entire perimeter to seat the adhesive.

After your Microsoft Surface Go charging port repair

Power the Surface Go back on and test the charging port repair function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Microsoft Surface Go job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.

Keep learning

Explore more Microsoft Surface Go repair context in the encyclopedia, or open related DIY guides.

Repair encyclopediaAll Surface Go guides
logo_footer

Stay in the loop

Get new guides, reviews, and repair news.

Quick Links

Explore

    © 2026 LML Repair. All rights reserved.