Tablet · Microsoft · Surface Pro X
Microsoft Surface Pro X Screen Replacement
Screen Replacement guide for the Microsoft Surface Pro X
Before you begin
Tools
- Heat gun or hair dryer
- Suction cup
- Guitar picks or plastic opening picks
- Precision Torx screwdriver set
- Plastic spudger
- Tweezers
- SIM eject tool
Parts / materials
- Replacement Surface Pro X display assembly
- Pre-cut display adhesive strips
- 91% Isopropyl alcohol
- Microfiber cleaning cloth
Safety
- Wear protective safety glasses to guard against sharp glass splinters from damaged screens.
- Do not heat glass above 80°C (176°F) to prevent damage to internal battery cells.
- Disconnect battery or main power before disconnecting flex cables to prevent motherboard electrical shorts.
Overview
Step-by-step
- 1
Power off the tablet
1 minCompletely shut down your Surface Pro X and unplug all power adapters and external cables.
- 2
Eject SIM tray and SSD door
2 minUse a SIM eject tool to remove the SIM tray and open the rear door covering the removable SSD.
- 3
Heat perimeter of display
3 minApply a heat gun set to low heat along all four screen edges for 2 to 3 minutes to soften the frame adhesive.
- 4
Attach suction cup
1 minPlace a suction cup near the top edge of the glass screen assembly and press firmly to lock suction.
- 5
Create initial screen gap
2 minPull upward gently on the suction cup handle until a tiny gap opens between the glass and magnesium frame.
- 6
Insert opening pick
2 minSlide a thin plastic opening pick into the gap under the top glass edge no deeper than 3 millimeters.
- 7
Slice top screen adhesive
3 minSlide the pick across the top border of the display panel to slice through the perimeter adhesive tape.
- 8
Slice left edge adhesive
3 minWork the opening pick down the left side frame, keeping the pick shallow to avoid damaging webcams and sensors.
- 9
Slice right edge adhesive
3 minSlide an opening pick down the right edge of the screen to cut the adhesive tape completely.
- 10
Slice bottom edge adhesive
4 minCarefully slice along the bottom display border, avoiding deep insertion near sensitive flex cables.
- 11
Open display panel like a book
2 minGently swing the screen assembly open from the top edge, resting it flat next to the device chassis.
- 12
Remove display connector shield screws
3 minUnscrew the small Torx screws securing the metal shield cover over the motherboard display connector.
- 13
Detach display connector shield
1 minUse tweezers to lift and remove the metal shielding bracket protecting the display cable connection.
- 14
Disconnect display flex cable
2 minPry the display flex cable connector straight up from the motherboard socket using a plastic spudger.
- 15
Remove damaged display assembly
1 minLift the cracked screen off the frame completely and place it aside.
- 16
Clean residual adhesive
5 minScrape off old adhesive tape from the chassis frame edges using isopropyl alcohol and a plastic tool.
- 17
Apply new adhesive tape
4 minAlign and lay down fresh double-sided pre-cut adhesive strips around the perimeter of the tablet frame.
- 18
Connect replacement display cable
2 minPress the flex cable connector of the new screen into the motherboard socket until it snaps in place.
- 19
Reinstall display connector shield
3 minPosition the metal shield back over the connector and tighten the Torx securing screws.
- 20
Test new screen functionality
3 minPower on the Surface Pro X temporarily to verify touch and display performance before final sealing.
- 21
Seal display to frame
3 minAlign the screen panel accurately with the chassis and press firmly along all edges to seal the adhesive.
After your Microsoft Surface Pro X screen replacement
Power the Surface Pro X back on and test the screen replacement function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Microsoft Surface Pro X job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Keep learning
Explore more Microsoft Surface Pro X repair context in the encyclopedia, or open related DIY guides.
