Tablet · Microsoft · Surface Pro 9
Microsoft Surface Pro 9 Charging Port Repair
Charging Port Repair guide for the Microsoft Surface Pro 9
Before you begin
Tools
- Heat gun or iOpener
- Suction handle
- Opening picks
- Torx T3 screwdriver
- Torx T5 screwdriver
- Plastic spudger
- Tweezers
Parts / materials
- Replacement Surface Pro 9 Surface Connect port assembly
- Pre-cut display adhesive strips
- Isopropyl alcohol (99%)
Safety
- Wear safety glasses to protect eyes from potential glass splinters during screen removal.
- Disconnect the battery before servicing internal cables to prevent short circuits.
- Handle the lithium-ion battery with care to avoid punctures or bends.
Overview
Step-by-step
- 1
Power off the Surface Pro 9
1 minShut down Windows completely and unplug all external cables and accessories.
- 2
Heat the glass edges
3 minApply a heat gun or heated iOpener along the perimeter of the screen for two minutes to soften the display adhesive.
- 3
Attach a suction handle
1 minPlace a suction handle near the top edge of the screen and press down to create a firm seal.
- 4
Insert an opening pick
2 minPull up gently on the suction handle to create a tiny gap, then slide a thin opening pick under the glass.
- 5
Slice perimeter adhesive
4 minSlide the pick around all four edges of the screen, keeping it shallow to avoid damaging internal cables.
- 6
Open the display assembly
1 minCarefully lift the left edge of the display and pivot it open like a book to access the motherboard connectors.
- 7
Remove the display shield screws
2 minUse a Torx screwdriver to remove the screws holding the metal display cable shield in place.
- 8
Detach the display flex cable
1 minUse a plastic spudger to pry the display press connector straight up from the motherboard.
- 9
Remove the screen
1 minLift the display assembly away completely and set it in a safe, soft location.
- 10
Unbolt the battery shield
2 minRemove the Torx screws securing the metal battery connector shield near the lower edge of the motherboard.
- 11
Disconnect the battery
1 minPry the battery connector up from its socket on the motherboard to cut power to the device.
- 12
Remove the charging port bracket screws
2 minUnscrew the Torx screws securing the metal retention bracket over the Surface Connect charging port assembly.
- 13
Disconnect the charging port cable
1 minUse a spudger to lift the charging port flex cable connector off the motherboard socket.
- 14
Remove the old charging port
1 minLift the damaged Surface Connect port module out of its recess in the aluminum chassis.
- 15
Insert the new charging port
1 minAlign the replacement Surface Connect port module into the chassis housing slot.
- 16
Connect the port flex cable
1 minPress the flex cable connector firmly onto its motherboard socket until it clicks into place.
- 17
Reinstall the port bracket
2 minPosition the metal retention bracket over the port and tighten its Torx screws.
- 18
Reconnect the battery
1 minAlign and press the battery connector back into its receptacle on the motherboard.
- 19
Reinstall the battery shield
2 minPlace the battery shield cover over the connection and secure it with the original screws.
- 20
Reconnect the display cable
1 minAttach the display ribbon cable connector to the motherboard socket until seated properly.
- 21
Secure the display cable shield
2 minPlace the metal display shield back over the connector and tighten the retaining screws.
- 22
Clean old adhesive
3 minScrape off residual adhesive from the frame using a spudger and clean the surface with 99% isopropyl alcohol.
- 23
Apply new adhesive strips
3 minLay pre-cut adhesive strips precisely along the frame perimeters and peel off the protective backing.
- 24
Seal the display
2 minAlign the glass display with the chassis frame and press firmly around all edges to secure the bond.
After your Microsoft Surface Pro 9 charging port repair
Power the Surface Pro 9 back on and test the charging port repair function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Microsoft Surface Pro 9 job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Keep learning
Explore more Microsoft Surface Pro 9 repair context in the encyclopedia, or open related DIY guides.
