Tablet · Microsoft · Surface Pro 7
Microsoft Surface Pro 7 Battery Replacement
Battery Replacement guide for the Microsoft Surface Pro 7
Before you begin
Tools
- Heat gun or iOpener
- Plastic opening picks
- Spudger
- Suction cup
- Torx T3 screwdriver
- Torx T5 screwdriver
- Plastic card
- Tweezers
Parts / materials
- Microsoft Surface Pro 7 replacement battery
- Pre-cut screen adhesive strips
- Battery adhesive strips
- 90%+ Isopropyl alcohol
Safety
- Wear eye protection to guard against unexpected glass breakage when opening the screen.
- Do not bend, puncture, or apply direct metal tools to the lithium-ion battery.
- Ensure the device is powered off before opening to prevent electrical short circuits.
Overview
Step-by-step
- 1
Power off the device
1 minTurn off your Surface Pro 7 completely and unplug all external power sources and accessories.
- 2
Heat the display edges
5 minApply a heat gun or iOpener around the outer edges of the screen for two minutes to soften the strong adhesive.
- 3
Attach a suction cup
2 minPlace a suction cup near the top center edge of the screen glass and gently pull upward to create a small gap.
- 4
Insert an opening pick
2 minSlide a thin plastic opening pick into the seam between the glass screen and the aluminum chassis.
- 5
Slice the display perimeter adhesive
10 minGently slide picks along all four edges to slice through the adhesive, taking care not to insert the pick deeper than 3 mm.
- 6
Lift the screen assembly
2 minCarefully tilt the top edge of the screen open like a book cover while keeping the bottom edge near the chassis.
- 7
Unscrew the display connector shield
3 minUse a Torx T3 screwdriver to remove the screws holding the metal bracket over the display connector.
- 8
Disconnect the screen ribbon cables
2 minUse the flat end of a spudger to pop the screen flex connectors straight up off the motherboard.
- 9
Remove the screen
1 minLift the display assembly away from the body and place it face-down on a clean, soft surface.
- 10
Unscrew the battery connector shield
3 minRemove the Torx screws securing the metal plate over the main battery interface connector.
- 11
Disconnect the battery cable
2 minPry the battery connector up from the motherboard using a plastic spudger to cut power to the device.
- 12
Remove internal heat shields
6 minUnscrew and remove the thin metal shield plates covering the motherboard and surrounding battery edges.
- 13
Apply adhesive remover
4 minDispense a few drops of high-concentration isopropyl alcohol along the top and side edges of the battery cells.
- 14
Pry up the old battery
12 minInsert a wide plastic card under the battery cells and slowly push forward to break the adhesive bond.
- 15
Remove the battery assembly
2 minLift the old battery out of the aluminum housing and set it aside safely for proper recycling.
- 16
Clean the battery recess
5 minWipe the interior aluminum frame with isopropyl alcohol to remove all residual glue and dirt.
- 17
Install new battery adhesive
3 minLay down fresh double-sided adhesive strips into the battery compartment on the aluminum frame.
- 18
Position the new battery
3 minAlign the replacement battery over the recess and press down firmly across all cells to seat it onto the adhesive.
- 19
Reconnect internal display and battery cables
8 minPlug the battery interface back in, replace all internal shields, and reconnect the display flex cables.
- 20
Apply new screen adhesive
5 minPlace pre-cut perimeter adhesive strips onto the chassis frame and press the display panel back into place.
After your Microsoft Surface Pro 7 battery replacement
Power the Surface Pro 7 back on and test the battery replacement function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Microsoft Surface Pro 7 job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Keep learning
Explore more Microsoft Surface Pro 7 repair context in the encyclopedia, or open related DIY guides.
