Tablet · Microsoft · Surface Pro 7 Plus
Microsoft Surface Pro 7 Plus Charging Port Repair
Charging Port Repair guide for the Microsoft Surface Pro 7 Plus
Before you begin
Tools
- Precision screwdriver set (Torx T3, T4)
- Heat gun or iOpener
- Plastic opening picks
- Suction cup
- Spudger
- Tweezers
- Anti-static wrist strap
Parts / materials
- Replacement Surface Connect charging port assembly
- Pre-cut display adhesive strips
- Isopropyl alcohol (90% or higher)
- Microfiber cloth
Safety
- Wear safety glasses to protect against potential glass splinters.
- Use heat-resistant gloves when handling hot components or the heat gun.
- Wear an anti-static wrist strap connected to a grounded surface during internal repairs.
Overview
Step-by-step
- 1
Power off the Surface Pro
1 minShut down the Surface Pro 7 Plus completely through the operating system. Unplug the charger and all external accessories.
- 2
Heat the screen perimeter
3 minUse a heat gun or heated iOpener along the outer glass edges for two minutes to soften the strong perimeter adhesive.
- 3
Attach a suction cup
2 minPlace a heavy-duty suction cup near the top edge of the display glass and pull upward gently to create a gap.
- 4
Insert an opening pick
2 minSlide a thin plastic opening pick into the gap between the display glass and the outer magnesium frame.
- 5
Slice through perimeter adhesive
10 minCarefully slide opening picks around all four edges of the screen, reheat as needed, and avoid inserting picks deeper than 3mm near the camera array.
- 6
Lift display glass
2 minGently tilt the screen up from the top edge like a book cover, taking care not to strain the attached display cables.
- 7
Unscrew the display cable shield
2 minRemove the two T3 Torx screws securing the metal shield over the main display connector.
- 8
Disconnect the display cable
2 minUse the flat end of a plastic spudger to pry the display press-fit connector straight up from the motherboard.
- 9
Isolate the battery power
3 minRemove the central battery contact screw and slide a plastic guitar pick underneath the battery contact pad to prevent shorts.
- 10
Remove motherboard EMI shield screws
5 minRemove the T4 Torx screws securing the large metal motherboard shield to the chassis frame.
- 11
Detach the motherboard shield
2 minUse tweezers to carefully lift the metal EMI shield off the internal components and place it aside.
- 12
Disconnect the Surface Connect flex cable
2 minPry the Surface Connect charging port ribbon cable connector straight up off the motherboard using a plastic spudger.
- 13
Unscrew the charging port module
2 minRemove the two T3 Torx screws holding the Surface Connect port housing to the inner frame.
- 14
Remove the damaged charging port
2 minLift the Surface Connect port assembly out of its recessed channel in the side of the magnesium body.
- 15
Position the new charging port
2 minPlace the replacement Surface Connect port into the chassis cutout, ensuring magnetic contacts face outward properly.
- 16
Secure charging port screws
2 minReinstall and tighten the two T3 Torx screws to firmly anchor the port to the side frame.
- 17
Attach Surface Connect cable
2 minAlign the press-fit flex connector over its motherboard socket and press down firmly until it snaps into place.
- 18
Reinstall motherboard shield
4 minPosition the metal EMI shield back over the board and secure it using the original T4 Torx screws.
- 19
Reconnect battery power
2 minRemove the plastic pick isolating the battery contact and reinstall the central battery contact screw.
- 20
Reconnect display cable and shield
3 minPress the screen connector back onto the motherboard, reposition its metal cover, and drive the two T3 screws.
- 21
Clean old display adhesive
5 minUse high-concentration isopropyl alcohol and a lint-free cloth to strip remaining adhesive off the frame and glass edges.
- 22
Apply fresh adhesive strips
5 minLay down pre-cut adhesive strips along the perimeter of the frame, peeling off the protective backing film.
- 23
Seal display to frame
3 minAlign the screen carefully over the frame and press firmly along all four edges to set the new adhesive seal.
After your Microsoft Surface Pro 7 Plus charging port repair
Power the Surface Pro 7 Plus back on and test the charging port repair function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Microsoft Surface Pro 7 Plus job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Keep learning
Explore more Microsoft Surface Pro 7 Plus repair context in the encyclopedia, or open related DIY guides.
