Tablet · Apple · iPad Pro 11 2nd Gen
Apple iPad Pro 11 2nd Gen Apple Pencil Port Repair
Apple Pencil Port Repair guide for the Apple iPad Pro 11 2nd Gen
Before you begin
Tools
- Precision driver set (Phillips & Torx T3)
- Plastic opening picks
- Suction handle
- Plastic spudger
- Tweezers
- iOpener or Heat gun
- Battery isolation pick
Parts / materials
- Replacement Apple Pencil charging port module
- Display adhesive strips
- Isopropyl alcohol (99%)
Safety
- Wear safety glasses to protect eyes from potential glass fragments during screen removal.
- Disconnect the battery or insert an isolation tool before touching internal logic board connectors.
- Keep heat application below 80°C (176°F) to avoid damaging the LCD matrix and internal battery cells.
Overview
Step-by-step
- 1
Heat Display Edges
3 minApply a heated iOpener or heat gun around the perimeter of the screen for two minutes to soften the frame adhesive.
- 2
Attach Suction Handle
2 minPlace a suction handle near the top edge of the screen and pull up firmly to create a small gap.
- 3
Insert Opening Pick
2 minSlide a thin plastic opening pick into the gap between the glass display and the aluminum frame.
- 4
Slice Perimeter Adhesive
8 minCarefully slide opening picks around all four edges of the display, keeping the pick shallow to avoid damaging internal cables.
- 5
Lift Display Assembly
3 minGently lift the top edge of the screen like a book page, taking care not to strain the flex cables along the bottom edge.
- 6
Unscrew Logic Board Shield
3 minRemove the five Phillips screws securing the display connector shield to the logic board.
- 7
Remove Cable Shield
1 minUse precision tweezers to lift the metal shield off the logic board connectors.
- 8
Disconnect Battery Connector
2 minInsert a plastic battery isolation pick beneath the battery contact elbow to disconnect power from the board.
- 9
Disconnect Display Cables
3 minUse the flat end of a spudger to detach the display flex cables and ambient light sensor cable from the logic board.
- 10
Remove Display Assembly
1 minLift the display assembly away from the frame and place it safely in a clean workspace.
- 11
Unscrew Pencil Charger Shield
3 minRemove the T3 Torx screws securing the Apple Pencil charging bracket along the side frame.
- 12
Disconnect Pencil Flex Cable
2 minUse a plastic spudger to gently pop the Pencil charger flex cable connector off its logic board socket.
- 13
Heat Frame Edge
2 minApply direct mild heat to the outer aluminum frame adjacent to the charging coil for one minute.
- 14
Pry Pencil Charger Module
3 minInsert a plastic spudger under the magnetic charging assembly and peel it away from the frame adhesive.
- 15
Install Replacement Module
3 minPosition the new Pencil charging port module into the frame channel and press firmly to seat the adhesive.
- 16
Attach Charger Flex Cable
2 minAlign the flex cable press connector over the logic board socket and press down until it snaps in place.
- 17
Reinstall Retaining Bracket
3 minPlace the metal shield bracket over the charging module and tighten the original T3 Torx screws.
- 18
Reconnect Screen and Test
5 minAttach the display cables, remove the battery isolation pick, and snap an Apple Pencil to the side to verify charging before re-sealing.
After your Apple iPad Pro 11 2nd Gen apple pencil port repair
Power the iPad Pro 11 2nd Gen back on and test the apple pencil port repair function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Apple iPad Pro 11 2nd Gen job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Keep learning
Explore more Apple iPad Pro 11 2nd Gen repair context in the encyclopedia, or open related DIY guides.
