Tablet · Apple · iPad Mini 5
Apple iPad Mini 5 Charging Port Repair
Charging Port Repair guide for the Apple iPad Mini 5
Before you begin
Tools
- Heat gun or hair dryer
- Suction cup
- Guitar picks for prying
- Precision screwdriver set
- Plastic prying tools
- Tweezers
- Soldering iron
- Desoldering braid
- PCB holder clamp
Parts / materials
- Replacement iPad Mini 5 Lightning Port
- Flux
- Solder
- 99% Isopropyl alcohol
- Pre-cut display adhesive strips
Safety
- Wear safety glasses to protect eyes from hot solder splatter.
- Perform soldering work in a well-ventilated area or use a fume extractor.
- Disconnect the battery before touching internal board components with metal tools.
- Do not bend or puncture the battery while prying up the logic board.
Overview
Step-by-step
- 1
Heat the Display Edges
3 minApply heat along the outer edges of the screen using a heat gun to soften the display adhesive beneath.
- 2
Attach the Suction Cup
2 minPlace a suction cup near the bottom edge of the display glass and pull upward gently to create a small gap.
- 3
Insert an Opening Pick
2 minSlide a plastic opening pick into the gap between the glass screen and the aluminum frame.
- 4
Slice the Screen Adhesive
5 minCarefully slide the pick around the perimeter to slice through the adhesive, taking extra care near the front camera and home button.
- 5
Open the Display Assembly
2 minGently lift the left side of the display screen and swing it open like a book frame.
- 6
Unscrew the Logic Board Shield
3 minRemove the four Phillips #000 screws holding the display cable metal shield in place.
- 7
Remove the Metal Shield
1 minLift and remove the metal shield using tweezers to reveal the underlying flex cable connectors.
- 8
Disconnect the Battery Cable
2 minInsert a plastic spudger beneath the battery connector and lift it straight up to cut power to the board.
- 9
Disconnect the Screen Flex Cables
2 minCarefully pry up the display and digitizer flex cables from their board sockets using a spudger.
- 10
Remove the Display Assembly
1 minLift the display assembly completely off the iPad chassis and set it safely aside.
- 11
Unscrew Board Brackets
4 minRemove the Phillips screws securing the upper and lower logic board retaining brackets.
- 12
Disconnect Antenna Cables
2 minUse fine tweezers to gently pop off the coaxial antenna connectors from the logic board.
- 13
Warm the iPad Enclosure
3 minApply heat to the back of the aluminum case to soften the strong glue holding the logic board.
- 14
Pry Up the Logic Board
4 minGently insert a plastic spudger under the logic board and pry it loose from the chassis frame.
- 15
Secure the Board in a Clamp
2 minPlace the logic board into a PCB holder or vice to keep it stable during soldering work.
- 16
Apply Liquid Soldering Flux
1 minApply a generous amount of flux across the lightning connector pin joints and ground anchors.
- 17
Desolder Port Anchor Pins
8 minUse a soldering iron and desoldering braid to wick away solder from the structural anchor pins and contact pads.
- 18
Remove Damaged Port
2 minGently pull the old lightning port off the board using tweezers once all solder joints are clear.
- 19
Clean Logic Board Pads
2 minClean the bare solder pads thoroughly using a cotton swab dipped in 99% isopropyl alcohol.
- 20
Solder the Replacement Port
10 minPosition the new lightning connector, apply fresh flux, and solder each pin firmly to the logic board pads.
- 21
Reinstall the Logic Board
5 minApply fresh adhesive to the enclosure, press the logic board back into position, and secure all board screws.
- 22
Reconnect Cables and Display
6 minPlug in antenna connectors, display cables, and battery, then screw down the metal shield before resealing the screen.
After your Apple iPad Mini 5 charging port repair
Power the iPad Mini 5 back on and test the charging port repair function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Apple iPad Mini 5 job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Keep learning
Explore more Apple iPad Mini 5 repair context in the encyclopedia, or open related DIY guides.
