Tablet · Apple · iPad Mini 5
Apple iPad Mini 5 Apple Pencil Port Repair
Apple Pencil Port Repair guide for the Apple iPad Mini 5
Before you begin
Tools
- Heat gun or hair dryer
- Suction cups
- Guitar picks for prying
- Precision screwdriver set
- Plastic prying tools
- Tweezers
- Soldering iron
- Solder wick
Parts / materials
- Replacement Lightning port flex assembly
- Pre-cut display adhesive strips
- Liquid soldering flux
- Rosin-core solder
- 99% Isopropyl alcohol
Safety
- Wear protective safety glasses when soldering and handling glass.
- Perform soldering in a well-ventilated area to avoid breathing fumes.
- Disconnect battery power immediately after opening the device to prevent short circuits.
Overview
Step-by-step
- 1
Heat Display Edges
3 minApply a heat gun evenly around the outer borders of the screen to soften the perimeter adhesive.
- 2
Attach Suction Cup
1 minPlace a suction cup on the lower portion of the glass panel, near the home button.
- 3
Insert Opening Pick
2 minPull up on the suction cup to create a seam, then insert a plastic guitar pick under the glass.
- 4
Slice Perimeter Adhesive
4 minSlide picks carefully along the left, top, and right sides to separate the adhesive.
- 5
Open Display Assembly
1 minGently tilt the screen upward from the top edge like a book, taking care not to strain bottom cables.
- 6
Unscrew Display Shield
2 minRemove the four Phillips screws securing the metal shield over the logic board connectors.
- 7
Remove Cable Shield
1 minLift the metal shield off the logic board using precision tweezers.
- 8
Disconnect Battery Connector
1 minSlide a plastic spudger beneath the battery contact connector to isolate electrical power.
- 9
Disconnect Display Cables
2 minPry the LCD display and digitizer press connectors directly up from their sockets.
- 10
Disconnect Home Button Flex
1 minUnsnap the home button ribbon connector from the logic board.
- 11
Separate Display Assembly
1 minLift the entire screen assembly off the iPad chassis and set it in a safe area.
- 12
Remove Lower Bracket Screws
2 minUnscrew the bracket holding the lower logic board section and Lightning port assembly.
- 13
Remove Lower Shield Bracket
1 minLift away the metal retention bracket from the bottom of the case.
- 14
Disconnect Antenna Cables
2 minPry the two coaxial antenna cable heads off their logic board sockets.
- 15
Remove Port Mounting Screws
2 minRemove the two screws securing the Lightning charging port to the aluminum frame.
- 16
Heat Lower Logic Board
2 minWarm the lower rear casing with a heat gun to soften the strong glue beneath the board tail.
- 17
Pry Up Board Assembly
3 minGently lift the logic board tail and Lightning port flex using a flat prying tool.
- 18
Desolder Lightning Port Connections
8 minApply heat with a soldering iron to release the soldered pins joining the port flex to the board.
- 19
Clean Board Contact Pads
4 minApply liquid flux and solder wick to clear residual solder from the board pads.
- 20
Position Replacement Port
3 minAlign the new Lightning port flex pins precisely over the cleaned board solder pads.
- 21
Solder New Port Assembly
8 minSolder each pin on the new port assembly securely to its corresponding logic board pad.
- 22
Secure Port Screws
2 minReinstall the two mounting screws to lock the Lightning port housing into the outer frame.
- 23
Reconnect Antenna Cables
2 minPress the coaxial antenna connectors down until they snap into their board sockets.
- 24
Attach Display and Home Flexes
3 minAlign and press down the home button, digitizer, and LCD flex connectors onto the board.
- 25
Reconnect Battery Power
1 minRemove the plastic isolation pick and press the battery connector back into place.
- 26
Reinstall Metal Display Shield
2 minPlace the shield bracket back over the board connectors and tighten the four Phillips screws.
- 27
Apply Pre-Cut Adhesive Strips
4 minApply fresh pre-cut adhesive tape along the outer perimeter of the aluminum enclosure.
- 28
Seal Display Panel
3 minAlign the screen assembly over the body, press firmly along all edges, and warm slightly to bond.
After your Apple iPad Mini 5 apple pencil port repair
Power the iPad Mini 5 back on and test the apple pencil port repair function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Apple iPad Mini 5 job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Keep learning
Explore more Apple iPad Mini 5 repair context in the encyclopedia, or open related DIY guides.
