Tablet · Apple · iPad Mini 2
Apple iPad Mini 2 Apple Pencil Port Repair
Apple Pencil Port Repair guide for the Apple iPad Mini 2
Before you begin
Tools
- Precision screwdriver set
- Plastic opening tools
- Heat gun or iOpener
- Tweezers
- Suction cup
- Spudger
- Soldering iron
- Opening picks
Parts / materials
- iPad Mini 2 replacement charging port flex cable
- Pre-cut screen adhesive strips
- 99% Isopropyl alcohol
- Rosin core solder
Safety
- Wear protective eyewear while heating glass and soldering components.
- Operate the soldering iron in a well-ventilated area.
- Disconnect battery contacts prior to major component work to prevent electrical shorts.
Overview
Step-by-step
- 1
Heat the Screen Perimeter
3 minApply a heated iOpener or heat gun around the front edges of the iPad Mini 2 for 2-3 minutes to soften the display adhesive.
- 2
Attach Suction Cup
1 minPlace a suction cup onto the glass digitizer near the bottom home button edge and press firmly to secure it.
- 3
Insert Opening Pick
2 minPull up on the suction cup to create a small gap, then insert an opening pick beneath the glass.
- 4
Slice Perimeter Adhesive
4 minSlide the opening pick around the top and side edges to cut through the remaining adhesive strips.
- 5
Open the Digitizer Glass
2 minGently swing the glass digitizer open from the left side like a book page, keeping the flex cable intact.
- 6
Remove LCD Corner Screws
2 minUse a Phillips screwdriver to unbolt the four screws located at each corner of the LCD panel frame.
- 7
Lift the LCD Display
2 minInsert a plastic spudger under the top edge of the LCD display and carefully lift it up from the frame.
- 8
Fold LCD Display Down
1 minPivot the LCD display downward over the open digitizer glass to expose the internal shield plate.
- 9
Unscrew EMI Shield
3 minRemove the screws securing the large metal display shield plate to the inner case.
- 10
Remove EMI Shield
1 minLift the metal EMI shield out of the device using tweezers and place it aside.
- 11
Disconnect LCD Cable
1 minPry the LCD display flex connector straight up from its logic board socket with a plastic spudger.
- 12
Disconnect Digitizer Cable
1 minDisconnect the digitizer flex cables from their sockets on the logic board using a spudger.
- 13
Set Display Assemblies Aside
1 minLift both the digitizer glass and LCD panel completely away from the iPad frame and store them safely.
- 14
Unscrew Antenna Bracket
2 minRemove the screws holding down the lower metal antenna brackets near the speaker modules.
- 15
Disconnect Antenna Cables
2 minPry up the coaxial antenna connectors from the logic board using fine tweezers.
- 16
Remove Charging Port Screws
2 minUnbolt the mounting screws securing the Lightning charging port to the bottom aluminum enclosure.
- 17
Heat Lower Enclosure
2 minApply mild heat to the lower rear case to soften the adhesive holding down the charging port flex cable.
- 18
Detach Old Charging Port Flex
3 minGently slide a opening pick under the flex cable to detach it from the rear case and logic board solder joint.
- 19
Clean Board Contact Pads
2 minWipe the solder contact pads on the logic board with a cotton swab dampened in 99% isopropyl alcohol.
- 20
Align New Charging Port Flex
2 minPosition the new replacement charging port into the lower housing, aligning the mounting holes and contact pads.
- 21
Solder New Connector Pads
8 minCarefully solder the new charging port flex connector pads to the designated points on the logic board.
- 22
Secure Charging Port Screws
2 minReinstall and tighten the mounting screws securing the port assembly to the bottom frame.
- 23
Reconnect Antenna Cables
2 minSnap the coaxial antenna connectors securely back into their logic board sockets.
- 24
Reinstall Antenna Bracket
2 minPlace the antenna bracket over the speakers and tighten its retaining screws.
- 25
Reconnect Display Connectors
2 minAttach the digitizer and LCD flex cables back onto their respective logic board sockets.
- 26
Reinstall EMI Shield
3 minSet the metal shield plate back over the logic board and tighten all securing screws.
- 27
Secure LCD Display Screws
2 minLower the LCD panel into position and reinstall the four corner screws.
- 28
Seal Digitizer Glass
4 minApply fresh pre-cut adhesive strips to the edges and press the digitizer glass down firmly to seal.
After your Apple iPad Mini 2 apple pencil port repair
Power the iPad Mini 2 back on and test the apple pencil port repair function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Apple iPad Mini 2 job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Keep learning
Explore more Apple iPad Mini 2 repair context in the encyclopedia, or open related DIY guides.
