Phone · Samsung · Galaxy S24 Plus
Samsung Galaxy S24 Plus Speaker Repair
Speaker Repair guide for the Samsung Galaxy S24 Plus
Before you begin
Tools
- Heat gun or hair dryer
- Suction cup tool
- Plastic prying tools
- Phillips #000 screwdriver
- Spudger tool
- Tweezers
- Anti-static wrist strap
Parts / materials
- Replacement Galaxy S24 Plus loudspeaker module
- Pre-cut back cover adhesive gasket
- 99% Isopropyl alcohol
Safety
- Wear eye protection when heating and prying glass components.
- Do not puncture, bend, or apply pressure to the internal battery.
- Ensure the device is powered off before starting repairs.
Overview
Step-by-step
- 1
Power Off Galaxy S24 Plus
1 minPress and hold the Side and Volume Down buttons, then tap Power Off on the screen. Ensure the device is completely powered down.
- 2
Heat Rear Glass Cover
2 minApply heat with a heat gun or hair dryer around the outer edges of the back cover for 2 minutes to soften the adhesive.
- 3
Attach Suction Cup
1 minPlace a suction cup near the bottom edge of the back cover and press firmly to create a secure seal.
- 4
Insert Opening Pick
2 minPull up on the suction cup to create a small gap, then insert a plastic opening pick under the glass back cover.
- 5
Slice Perimeter Adhesive
3 minSlide the plastic pick around all four edges of the back cover to cut through the factory adhesive tape.
- 6
Remove Rear Glass Cover
1 minLift the rear glass cover off the chassis and place it on a clean, soft surface.
- 7
Remove Wireless Coil Screws
2 minUse a Phillips #000 screwdriver to remove the 6 screws securing the top wireless charging pad assembly.
- 8
Peel Away Wireless Charging Coil
2 minGently peel up the wireless charging coil assembly from the motherboard shield and move it out of the way.
- 9
Remove Loudspeaker Assembly Screws
2 minUse a Phillips #000 screwdriver to remove the 6 screws holding down the lower loudspeaker module.
- 10
Pry Out Defective Loudspeaker
2 minInsert the flat end of a spudger under the top edge of the speaker housing and gently pry it up out of the frame.
- 11
Clear Debris from Recess
2 minUse tweezers and isopropyl alcohol to clear any leftover adhesive strips or dust from the speaker cavity.
- 12
Insert Replacement Loudspeaker
2 minAlign the new loudspeaker module over the bottom cavity and press it firmly into position until flush.
- 13
Secure Loudspeaker Screws
2 minReinstall the 6 Phillips #000 screws into the loudspeaker module to lock it into the chassis.
- 14
Reattach Wireless Charging Coil
2 minLay the wireless charging pad back over the motherboard and secure it with its 6 Phillips #000 screws.
- 15
Clean Chassis Adhesive Rails
3 minRemove old adhesive remnants from the frame perimeter using a spudger and isopropyl alcohol.
- 16
Apply Pre-Cut Back Cover Adhesive
2 minAlign the new pre-cut adhesive sticker onto the frame, press down around the rim, and remove the plastic liner.
- 17
Seal Rear Cover
2 minAlign the back glass cover over the frame and press firmly along all edges to seat the adhesive seal.
After your Samsung Galaxy S24 Plus speaker repair
Power the Galaxy S24 Plus back on and test the speaker repair function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Samsung Galaxy S24 Plus job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Keep learning
Explore more Samsung Galaxy S24 Plus repair context in the encyclopedia, or open related DIY guides.
