Step-by-step

1. 1

   Power Off Phone

   1 min

   Press and hold the Power and Volume Down buttons, then select Power Off on the screen. Disconnect all cables before starting.

2. 2

   Heat Back Glass

   3 min

   Apply a heated pad or heat gun around the perimeter of the back cover for 2 minutes. This softens the factory adhesive sealing the glass panel.

3. 3

   Attach Suction Handle

   1 min

   Place a suction cup onto the lower third of the back glass. Pull upward firmly to create a microscopic gap between the glass and the frame.

4. 4

   Insert Opening Pick

   2 min

   Insert a thin plastic opening pick into the seam created by the suction cup. Do not insert the pick deeper than 3 mm to avoid internal damage.

5. 5

   Slice Lower Edge Adhesive

   2 min

   Slide the pick along the bottom edge of the phone to cut through the perimeter adhesive sealant.

6. 6

   Slice Side Adhesive

   2 min

   Move the pick around the bottom corners and up both side edges to slice through the remaining adhesive strips.

7. 7

   Slice Top Edge Adhesive

   2 min

   Carefully slide the pick across the top edge. Avoid inserting near the camera bump to prevent glass cracking.

8. 8

   Remove Back Glass

   1 min

   Lift the back glass straight off the frame and set it aside on a clean work surface.

9. 9

   Unscrew Wireless Charging Assembly

   2 min

   Remove the five Phillips #00 screws securing the wireless charging coil bracket to the frame.

10. 10

    Disconnect Wireless Coil Connector

    1 min

    Use a plastic spudger to pry the wireless charging flex cable directly up from its motherboard socket.

11. 11

    Lift Off Wireless Coil Assembly

    1 min

    Peel up the graphite sheet and carefully remove the wireless charging coil assembly from the chassis.

12. 12

    Disconnect Battery Cable

    1 min

    Pry the battery press connector straight up off the motherboard using a plastic spudger to cut all power.

13. 13

    Unscrew Lower Speaker Housing

    2 min

    Remove the five Phillips #00 screws securing the loudspeaker module at the bottom of the phone.

14. 14

    Remove Speaker Housing

    1 min

    Insert a spudger under the speaker module edge and lift it out of the frame.

15. 15

    Disconnect Main Interconnect Cables

    2 min

    Disconnect the main and display flex cables spanning across the battery well using a plastic spudger.

16. 16

    Apply Adhesive Solvent

    3 min

    Drip a small amount of high-purity isopropyl alcohol or adhesive remover into the gaps around the battery perimeter.

17. 17

    Insert Plastic Pry Tool

    2 min

    Work a flat plastic card or heavy-duty opening pick under the side edge of the battery cell.

18. 18

    Pry Up Battery

    3 min

    Gently lever the battery upward from the frame, working slowly to let the solvent break the glue bonds.

19. 19

    Lift Battery Out

    1 min

    Remove the old battery from the device and store it safely for proper chemical disposal.

20. 20

    Clean Battery Recess

    2 min

    Wipe away remaining adhesive residue inside the battery compartment using a lint-free wipe dipped in isopropyl alcohol.

21. 21

    Apply New Battery Adhesive

    2 min

    Lay down double-sided battery adhesive strips precisely into the clean battery well recess.

22. 22

    Press New Battery Into Place

    1 min

    Align the replacement battery into the frame and press down firmly across its surface for 10 seconds.

23. 23

    Reconnect Interconnect Cables

    2 min

    Snap the main and display flex cables back into their respective board sockets until you feel them click.

24. 24

    Reinstall Speaker Housing

    2 min

    Seat the speaker module into the bottom frame and re-tighten its five Phillips screws.

25. 25

    Connect Battery Cable

    1 min

    Align and press the battery terminal connector straight down onto the motherboard receptacle.

26. 26

    Reinstall Wireless Coil Assembly

    2 min

    Position the wireless coil module over the motherboard, press the connector down, and secure its five Phillips screws.

27. 27

    Reseal Back Glass

    3 min

    Apply a fresh pre-cut adhesive gasket to the frame edge, line up the back glass panel, and press firmly along all edges to seal.