Phone · Samsung · Galaxy S22 Ultra
Samsung Galaxy S22 Ultra Speaker Repair
Speaker Repair guide for the Samsung Galaxy S22 Ultra
Before you begin
Tools
- Precision screwdriver set (Phillips #000)
- Plastic prying tools
- Suction cup tool
- Heat gun or hair dryer
- Spudger tool
- Tweezers
Parts / materials
- Replacement Galaxy S22 Ultra loudspeaker assembly
- Pre-cut back cover adhesive tape
- 90%+ Isopropyl alcohol
- Microfiber cleaning cloth
Safety
- Wear eye protection when heating glass to protect against possible splintering.
- Disconnect the battery before touching any internal components to prevent electrical shorts.
- Do not heat the back cover above 80°C to prevent damage to the AMOLED display and battery.
Overview
Step-by-step
- 1
Eject the S-Pen
1 minPress in on the S-Pen tip to unlock it, then slide it completely out of the bottom slot.
- 2
Heat the Back Glass
3 minApply a heat gun or hairdryer around the edges of the back glass for 2 to 3 minutes to soften the adhesive seal.
- 3
Attach Suction Cup
2 minPress a suction cup onto the lower section of the back glass and pull upward firmly to create a seam.
- 4
Insert Opening Tool
2 minInsert a plastic prying tool into the seam created by the suction cup along the bottom edge.
- 5
Slice Perimeter Adhesive
4 minSlide the plastic prying tool carefully around all four edges of the back glass to slice through the remaining adhesive.
- 6
Remove the Back Cover
1 minLift the back glass straight up off the phone chassis and set it safely aside.
- 7
Unscrew Wireless Charging Bracket
3 minUse a Phillips #000 screwdriver to remove the 5 screws holding the top wireless charging assembly.
- 8
Disconnect Wireless Charging Coil
2 minGently unclip the NFC press connector with a spudger and peel the wireless coil off the battery.
- 9
Disconnect the Battery
1 minPry the battery connector straight up from its motherboard socket using the flat end of a spudger.
- 10
Unscrew Loudspeaker Module
3 minRemove the 6 Phillips #000 screws securing the bottom loudspeaker assembly to the frame.
- 11
Pry Out Loudspeaker Module
2 minInsert the tip of a spudger under the notch of the loudspeaker housing and lift it clear of the lower frame.
- 12
Insert New Loudspeaker Module
2 minAlign the replacement loudspeaker module with the lower housing cavity and press it down flush into position.
- 13
Fasten Loudspeaker Screws
2 minReinstall and tighten the 6 Phillips #000 screws to secure the speaker module to the lower chassis.
- 14
Reconnect the Battery
1 minAlign the battery press connector over its motherboard socket and gently press down until it clicks into place.
- 15
Reinstall Wireless Charging Bracket
3 minLay the wireless charging coil flat, connect its press joint, and replace the 5 Phillips #000 screws.
- 16
Reseal the Back Glass
3 minApply new custom-cut adhesive to the rear frame, align the back glass, and press firmly along the perimeter to seal.
- 17
Reinsert the S-Pen
1 minPush the S-Pen back into its dedicated slot at the bottom until it clicks into its locked position.
After your Samsung Galaxy S22 Ultra speaker repair
Power the Galaxy S22 Ultra back on and test the speaker repair function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Samsung Galaxy S22 Ultra job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Keep learning
Explore more Samsung Galaxy S22 Ultra repair context in the encyclopedia, or open related DIY guides.
