Phone · OnePlus · Nord N200 5G
OnePlus Nord N200 5G Speaker Repair
Speaker Repair guide for the OnePlus Nord N200 5G
Before you begin
Tools
- Phillips #00 screwdriver
- Heat gun or iOpener
- Suction cup
- Plastic opening picks
- Spudger
- SIM card eject tool
- Tweezers
Parts / materials
- Replacement loudspeaker module
- Pre-cut back cover adhesive
- High-concentration isopropyl alcohol
Safety
- Wear safety glasses to protect against flying glass splinters during back cover removal.
- Do not apply excess heat over the battery area to prevent thermal damage.
- Use non-conductive plastic prying tools when working around internal components.
Overview
Step-by-step
- 1
Power down the device
1 minPress and hold the Power button, then select Power Off on the screen to shut down the phone completely.
- 2
Eject the SIM tray
1 minInsert a SIM eject tool into the small hole on the left edge of the phone to pop out the SIM card tray.
- 3
Heat the rear glass panel
2 minApply a heat gun or iOpener around the outer edges of the back cover for two minutes to soften the adhesive.
- 4
Attach a suction cup
1 minPress a suction cup firmly onto the lower portion of the rear panel, close to the bottom edge.
- 5
Create a prying gap
2 minPull up on the suction cup with firm pressure to lift the rear panel slightly off the frame and create a thin gap.
- 6
Insert a plastic opening pick
1 minSlide the tip of a plastic opening pick directly into the gap between the rear cover and the phone frame.
- 7
Slice the edge adhesive
4 minSlide the opening pick along the bottom, sides, and top edges to separate the adhesive securing the rear panel.
- 8
Remove the rear panel
1 minLift the rear panel completely away from the frame and lay it on a clean surface.
- 9
Unscrew the speaker housing
3 minUse a Phillips #00 screwdriver to remove the seven Phillips screws securing the bottom speaker module.
- 10
Pry up the speaker module
2 minInsert the flat end of a spudger under the upper rim of the speaker housing and gently lever it upward to unclip it.
- 11
Remove the damaged loudspeaker
1 minGrasp the loudspeaker module with your fingers or tweezers and lift it out of the bottom chassis frame.
- 12
Install the replacement loudspeaker
2 minAlign the new loudspeaker module into the lower recess and press down firmly until the side plastic tabs snap into place.
- 13
Reinstall the housing screws
3 minDrive the seven Phillips #00 screws back into the speaker housing to secure the module to the frame.
- 14
Clean residual frame adhesive
3 minApply a few drops of isopropyl alcohol to a lint-free cloth and scrape off all remaining adhesive strips from the frame.
- 15
Apply fresh rear cover adhesive
3 minPeel and lay down new double-sided adhesive strips along the perimeter lip of the phone frame.
- 16
Reattach the rear panel
2 minAlign the back panel carefully with the phone body and press down along all four edges to seal the adhesive.
- 17
Reinsert the SIM tray
1 minPush the SIM card tray back into its slot on the left side of the device until it sits flush.
After your OnePlus Nord N200 5G speaker repair
Power the Nord N200 5G back on and test the speaker repair function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this OnePlus Nord N200 5G job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Keep learning
Explore more OnePlus Nord N200 5G repair context in the encyclopedia, or open related DIY guides.
