Phone · OnePlus · Nord N10 5G
OnePlus Nord N10 5G Charging Port Repair
Charging Port Repair guide for the OnePlus Nord N10 5G
Before you begin
Tools
- Precision screwdriver set
- Plastic opening tools
- Anti-static wrist strap
- Tweezers
- Suction cup
- Heat gun or hair dryer
Parts / materials
- Replacement charging port daughterboard
- Back cover adhesive tape
- Isopropyl alcohol (99%)
Safety
- Always disconnect the battery connector before removing or installing internal components.
- Wear safety glasses when heating the back glass and using sharp opening picks.
- Avoid using metal tools around the battery to prevent dangerous electrical short circuits.
Overview
Step-by-step
- 1
Power Down Device
1 minPress and hold the power button, then tap Power Off on the screen. Ensure the device is completely powered down before continuing.
- 2
Eject SIM Card Tray
1 minInsert a SIM eject tool or paperclip into the small hole on the left side of the frame. Push firmly to pop out the tray and remove it.
- 3
Heat Back Panel
3 minApply a heat gun or hair dryer around the outer edges of the rear cover for three minutes. This softens the adhesive securing the plastic panel.
- 4
Attach Suction Cup
1 minPlace a suction cup near the bottom edge of the back cover. Press down firmly to establish a secure suction seal.
- 5
Slice Perimeter Adhesive
4 minPull up on the suction cup to create a gap and insert an opening pick. Slide the pick around the entire perimeter to cut through the adhesive tape.
- 6
Disconnect Fingerprint Sensor
2 minGently lift the back panel from the left edge like a book. Use a spudger to pop the fingerprint sensor flex cable off the motherboard.
- 7
Unscrew Upper Midframe
3 minRemove the eleven Phillips #00 screws securing the upper plastic motherboard cover. Group and organize the screws for reassembly.
- 8
Remove Motherboard Cover
2 minInsert a plastic spudger under the edge of the motherboard shield and lift it free from the phone.
- 9
Disconnect Battery Flex Cable
1 minPry the battery connector straight up from its motherboard socket using a plastic spudger. This prevents electrical shorts while working on the device.
- 10
Unscrew Loudspeaker Module
2 minRemove the seven Phillips #00 screws securing the loudspeaker assembly over the lower daughterboard.
- 11
Remove Loudspeaker Module
2 minPry up the loudspeaker module using a flat opening tool and set it aside to reveal the charging port daughterboard.
- 12
Disconnect Main Interconnect Cable
1 minUse the flat end of a plastic spudger to detach the interconnect flex cable from the charging port board.
- 13
Disconnect Coaxial Antenna Cable
1 minGently pry the black coaxial antenna cable connector up off its board socket using precision tweezers.
- 14
Pry Up Charging Board
2 minInsert a plastic spudger beneath the charging port daughterboard. Carefully lever it upward to break the light adhesive holding it to the frame.
- 15
Position New Charging Board
2 minSet the new charging port daughterboard into the bottom recess of the frame. Press down lightly to seat it flush.
- 16
Attach Coaxial Antenna Cable
1 minAlign the antenna cable head over its socket on the new board and press straight down until it snaps in.
- 17
Attach Main Interconnect Cable
1 minAlign the interconnect ribbon flex connector over the socket and press down firmly until it clicks.
- 18
Reinstall Loudspeaker Assembly
2 minLower the loudspeaker module back over the daughterboard area and press it down into place.
- 19
Secure Loudspeaker Screws
2 minReinstall and tighten the seven Phillips #00 screws to hold the loudspeaker assembly in place.
- 20
Reconnect Battery Cable
1 minAlign the battery flex connector over its motherboard terminal and press down until it snaps securely into place.
- 21
Reinstall Motherboard Cover
3 minPlace the motherboard shield over the top assembly and secure it using the eleven Phillips #00 screws removed earlier.
- 22
Reconnect Fingerprint Sensor
2 minHold the back cover close to the frame and connect the fingerprint flex cable back to the motherboard socket.
- 23
Apply Fresh Adhesive
3 minClean remaining glue from the frame with isopropyl alcohol. Apply new pre-cut double-sided tape strips along the perimeter.
- 24
Seal Back Cover
2 minAlign the back cover with the frame and press firmly along all four edges. Reinsert the SIM card tray.
After your OnePlus Nord N10 5G charging port repair
Power the Nord N10 5G back on and test the charging port repair function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this OnePlus Nord N10 5G job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Keep learning
Explore more OnePlus Nord N10 5G repair context in the encyclopedia, or open related DIY guides.
