Skip to main content

Phone · OnePlus · Nord CE 5G

OnePlus Nord CE 5G Screen Replacement

Screen Replacement guide for the OnePlus Nord CE 5G

Difficult
~58 min
20 steps

Before you begin

Tools

  • Heat gun or hair dryer
  • Suction cup tool
  • Plastic prying tools
  • Precision screwdriver set (Phillips #00)
  • Spudger tool
  • SIM eject tool
  • Tweezers

Parts / materials

  • Double-sided adhesive strips
  • Isopropyl alcohol (90%+)
  • Microfiber cloth

Safety

  • Wear protective eyewear to avoid injury from flying glass fragments if the screen is cracked.
  • Use an anti-static wrist strap to prevent electrostatic discharge damage to internal electronics.
  • Do not puncture or bend the lithium-ion battery during disassembly.

Overview

# OnePlus Nord CE 5G Screen Replacement Repair Guide Action-specific screen replacement walkthrough for the OnePlus Nord CE 5G. About 58 minutes across 20 steps. This DIY guide walks through screen replacement on the OnePlus Nord CE 5G (Nord series phone). Before you open the device, confirm the exact model number on the OnePlus settings screen or rear housing so your replacement part matches the Nord CE 5G specifically—not a similar Nord sibling. Most DIY techs finish this OnePlus Nord CE 5G screen replacement in about 58 minutes when parts and tools are ready. Difficulty is rated advanced for this model. Recommended tools for this OnePlus Nord CE 5G job: Heat gun or hair dryer, Suction cup tool, Plastic prying tools, Precision screwdriver set (Phillips #00), Spudger tool, SIM eject tool, Tweezers. Parts and supplies: Double-sided adhesive strips, Isopropyl alcohol (90%+), Microfiber cloth. Power the Nord CE 5G off completely, remove SIMs/SD cards if present, and work on a clean, well-lit surface with a magnetic mat for screws. If a step feels wrong for your OnePlus Nord CE 5G, stop and compare the connector layout to the photos in this guide. When you prefer a same-day pro repair in Seattle instead, LML Repair can handle screen replacement for this model with tested parts and a workmanship warranty.

Step-by-step

  1. 1

    Power off the device

    1 min

    Press and hold the power button and volume up button simultaneously, then tap 'Power Off' on the screen.

  2. 2

    Eject the SIM card tray

    1 min

    Insert a SIM eject tool into the small hole on the left side of the frame and push firmly to pop out the tray.

  3. 3

    Heat the rear panel

    3 min

    Apply heat to the edges of the back cover with a heat gun for 2 to 3 minutes to soften the adhesive beneath.

  4. 4

    Slice the back cover adhesive

    4 min

    Press a suction cup near the bottom edge of the back panel, pull up, and slide a plastic opening pick under the seam.

  5. 5

    Remove the rear cover

    3 min

    Work the opening pick around all four edges to slice the remaining adhesive, then lift the back cover clear of the phone body.

  6. 6

    Unscrew the plastic midframe

    4 min

    Use a Phillips #00 screwdriver to remove all visible screws securing the midframe to the inner phone chassis.

  7. 7

    Unclip and remove the midframe

    3 min

    Insert a flat plastic spudger between the outer frame and the midframe to pop the plastic clips free along the perimeter.

  8. 8

    Disconnect the battery cable

    2 min

    Use the pointed end of a spudger to gently pry the battery flex cable connector straight up from the motherboard.

  9. 9

    Disconnect the display flex cable

    2 min

    Pry up the display connector from its socket on the motherboard using a plastic spudger.

  10. 10

    Heat the front display

    3 min

    Use a heat gun evenly across the front screen for 3 minutes to soften the strong adhesive bonding the OLED panel.

  11. 11

    Slice the screen adhesive

    5 min

    Attach a suction cup to the lower front glass, lift gently, and insert a thin plastic prying card into the edge gap.

  12. 12

    Separate the screen assembly

    4 min

    Carefully slide the prying card along all sides while guiding the display flex cable through the slot in the frame.

  13. 13

    Clean the frame rim

    5 min

    Scrape away leftover adhesive from the inner chassis ledge using a spudger, then wipe clean with high-percentage isopropyl alcohol.

  14. 14

    Apply new screen adhesive

    4 min

    Lay double-sided adhesive strips along the thin metal perimeter of the chassis frame, pressing firmly down.

  15. 15

    Route and seat the new screen

    3 min

    Thread the flex cable of the new display through the frame opening and gently press the display panel into position.

  16. 16

    Reconnect the display cable

    2 min

    Align the display flex connector over its socket on the motherboard and press down until it snaps in place.

  17. 17

    Reconnect the battery cable

    1 min

    Press the battery connector down onto the motherboard until you feel a firm click.

  18. 18

    Reinstall the midframe

    4 min

    Snap the midframe housing back over the chassis and tighten all Phillips screws removed earlier.

  19. 19

    Reseal and attach the rear panel

    3 min

    Apply fresh adhesive tape along the rear frame edges, align the back cover, and press firmly around all borders to seal.

  20. 20

    Reinsert the SIM card tray

    1 min

    Slide the SIM card tray back into its slot until flush with the outer frame.

After your OnePlus Nord CE 5G screen replacement

Power the Nord CE 5G back on and test the screen replacement function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this OnePlus Nord CE 5G job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.

Keep learning

Explore more OnePlus Nord CE 5G repair context in the encyclopedia, or open related DIY guides.

logo_footer

Stay in the loop

Get new guides, reviews, and repair news.

© 2026 LML Repair. All rights reserved.