Phone · Motorola · Moto G64 5G
Motorola Moto G64 5G Speaker Repair
Speaker Repair guide for the Motorola Moto G64 5G
Before you begin
Tools
- Precision screwdriver set (Phillips #000)
- Plastic prying tools
- Suction cup tool
- Heat gun or hair dryer
- Tweezers
- Spudger tool
- SIM eject tool
Parts / materials
- Replacement loudspeaker module for Moto G64 5G
- Rear cover adhesive strips
- 99% Isopropyl alcohol
Safety
- Always disconnect the battery before working near electrical components.
- Do not puncture or bend the internal battery during repair.
- Wear eye protection when heating glass and using isopropyl alcohol.
Overview
Step-by-step
- 1
Power Off the Phone
1 minPress and hold the power button, then select Power Off on the screen to shut down the device completely.
- 2
Eject the SIM Tray
1 minInsert a SIM eject tool into the pinhole on the upper left side of the frame and push firmly to pop out the tray.
- 3
Heat the Rear Cover
2 minUse a heat gun or hair dryer on low heat around the edges of the back panel for two minutes to soften the adhesive.
- 4
Attach the Suction Cup
1 minPlace a suction cup near the bottom edge of the back panel and pull upward to create a slight gap.
- 5
Slice the Back Cover Adhesive
3 minInsert a plastic prying tool into the gap and slide it carefully along all four edges to slice through the adhesive.
- 6
Lift Off the Rear Cover
2 minGently lift the back cover off the chassis and set it aside on a clean surface.
- 7
Unscrew the Lower Housing
3 minUse a Phillips #000 screwdriver to remove the screws securing the plastic lower speaker housing frame.
- 8
Pry Off the Speaker Frame
2 minInsert a flat spudger under the notch of the lower plastic housing cover and lift it free from the phone.
- 9
Disconnect the Battery Cable
1 minUse a plastic spudger to pry the battery flex cable connector straight up off the motherboard socket.
- 10
Remove the Old Speaker
2 minUse tweezers or a spudger to pry the loudspeaker module out from the lower plastic housing assembly.
- 11
Clean the Speaker Housing
2 minClear out any remaining adhesive residue or dust from the speaker recess using isopropyl alcohol and a lint-free cloth.
- 12
Insert the New Speaker
2 minAlign the new loudspeaker module into the lower housing bracket and press down evenly until seated.
- 13
Reconnect the Battery Cable
1 minAlign the battery flex connector with its motherboard socket and press down gently until it clicks into place.
- 14
Position the Lower Housing Frame
1 minSet the lower speaker frame assembly back into position over the bottom area of the phone chassis.
- 15
Reinstall Lower Frame Screws
3 minThread and tighten the Phillips #000 screws to secure the speaker housing back to the frame.
- 16
Apply Rear Cover Adhesive
3 minLay fresh pre-cut adhesive strips along the perimeter of the inner phone chassis.
- 17
Reattach the Rear Cover
2 minAlign the rear cover with the chassis frame and press firmly along the edges to seal the adhesive.
- 18
Reinsert the SIM Tray
1 minPush the SIM card tray back into the slot on the side of the phone until it sits flush.
After your Motorola Moto G64 5G speaker repair
Power the Moto G64 5G back on and test the speaker repair function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Motorola Moto G64 5G job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Keep learning
Explore more Motorola Moto G64 5G repair context in the encyclopedia, or open related DIY guides.
