Phone · Motorola · Moto G62 5G
Motorola Moto G62 5G Screen Replacement
Screen Replacement guide for the Motorola Moto G62 5G
Before you begin
Tools
- Heat gun or hair dryer
- Suction cup tool
- Plastic opening picks
- Spudger tool
- Precision screwdriver set (Phillips #000)
- Tweezers
- SIM eject tool
Parts / materials
- Replacement Motorola Moto G62 5G display
- Double-sided adhesive strips
- Isopropyl alcohol (99%)
- B-7000 adhesive
Safety
- Always disconnect the battery before working on internal electronics to prevent short circuits.
- Wear safety glasses to protect against flying glass splinters when removing a shattered screen.
- Avoid overheating the device with the heat gun to prevent damage to internal batteries and components.
Overview
Step-by-step
- 1
Eject the SIM tray
1 minInsert the SIM eject tool into the small hole beside the tray on the left edge. Push firmly to pop the tray out, then remove it completely.
- 2
Heat the rear cover
3 minApply a heat gun set to 80°C along the edges of the back cover for two minutes. This softens the factory adhesive securing the plastic rear panel.
- 3
Slice the rear adhesive
4 minPlace a suction cup on the lower portion of the back cover and pull upward to create a small gap. Insert a plastic opening pick and carefully slide it around all edges.
- 4
Remove the rear cover
1 minLift the rear cover away from the chassis. Set it aside on a clean surface.
- 5
Unscrew the mainboard bracket
3 minUse a Phillips #000 screwdriver to remove the screws securing the upper motherboard cover. Keep track of all screws for reassembly.
- 6
Remove the mainboard bracket
1 minGently lift the plastic mainboard bracket using a spudger and set it aside.
- 7
Disconnect the battery cable
1 minPry up the battery press connector from the motherboard using the flat edge of a plastic spudger. This prevents electrical shorts during repair.
- 8
Disconnect the fingerprint sensor
1 minUse a plastic spudger to gently pop off the side key fingerprint sensor ribbon flex cable connector from the board.
- 9
Unscrew the speaker enclosure
2 minRemove the Phillips screws holding down the speaker housing at the bottom of the device.
- 10
Remove the speaker enclosure
1 minPry up and remove the lower loudspeaker module to reveal the bottom sub-board connections.
- 11
Disconnect the display cable
1 minLocate the screen flex connector on the sub-board/mainboard junction and pop it off with a spudger.
- 12
Heat the display panel
3 minApply uniform heat across the front display using a heat gun for 2 to 3 minutes to loosen the screen glue.
- 13
Separate the display panel
4 minAttach a suction cup near the top edge of the front glass and pull up. Insert a thin opening tool between the frame and glass to cut through adhesive.
- 14
Lift the old display off
2 minGuide the display flex cable carefully through the frame slot as you lift the broken screen away.
- 15
Clean the frame edges
4 minScrape off residual glue from the frame bevels using a spudger and clean the surface with isopropyl alcohol.
- 16
Apply adhesive to the frame
3 minApply narrow pre-cut adhesive strips or a thin bead of B-7000 glue along the internal lip of the frame.
- 17
Thread the new display cable
2 minFeed the flex cable of the replacement screen through the slot in the phone frame.
- 18
Press the new screen into place
2 minAlign the replacement glass precisely inside the chassis frame and press firmly along all edges.
- 19
Connect the display cable
1 minSnap the display ribbon connector securely onto its socket on the board.
- 20
Reconnect the battery cable
1 minPress the battery connector straight down onto the motherboard until it clicks into place.
- 21
Reinstall the mainboard bracket
3 minPosition the mainboard shield over the top of the motherboard and secure it with its original screws.
- 22
Reinstall the speaker enclosure
2 minPlace the bottom speaker module back into position and tighten all remaining chassis screws.
- 23
Apply rear cover adhesive
2 minPlace new double-sided adhesive strips along the perimeter of the inner rear frame.
- 24
Attach the rear cover
2 minPress the plastic back cover firmly onto the device chassis to establish a complete seal.
- 25
Reinsert the SIM tray
1 minSlide the SIM card tray back into its slot on the side of the phone until it sits flush.
After your Motorola Moto G62 5G screen replacement
Power the Moto G62 5G back on and test the screen replacement function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Motorola Moto G62 5G job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Keep learning
Explore more Motorola Moto G62 5G repair context in the encyclopedia, or open related DIY guides.
