Phone · Motorola · Moto G54
Motorola Moto G54 Speaker Repair
Speaker Repair guide for the Motorola Moto G54
Before you begin
Tools
- Precision Phillips #00 screwdriver
- Heat gun or hair dryer
- Suction cup tool
- Plastic prying tools / opening picks
- Spudger tool
- Tweezers
- SIM eject tool
Parts / materials
- Replacement Moto G54 loudspeaker module
- Pre-cut rear cover adhesive strips
- 90%+ isopropyl alcohol
- Lint-free cleaning cloth
Safety
- Wear safety glasses to protect eyes when heating and prying plastic components.
- Do not overheat the rear panel to protect the internal battery from thermal damage.
- Ensure the device is powered off completely before loosening internal components.
- Use plastic non-conductive tools near open electronics to prevent short circuits.
Overview
Step-by-step
- 1
Power Off the Phone
1 minPress and hold the Power and Volume Up buttons simultaneously, then tap Power Off on the screen.
- 2
Remove the SIM Card Tray
1 minInsert a SIM eject tool into the hole next to the SIM tray on the upper left side of the device and press firmly to eject it.
- 3
Heat the Rear Cover Edges
2 minApply heat using a heat gun or hairdryer along the outer perimeter of the back cover for 2 minutes to soften the adhesive.
- 4
Attach Suction Cup
1 minPlace a suction cup near the bottom edge of the rear panel and gently pull upward to create a small gap.
- 5
Insert Opening Pick
1 minSlide a thin plastic opening pick into the seam created between the back panel and the frame.
- 6
Slice Rear Panel Adhesive
3 minCarefully slide the pick around all four edges of the back cover to cut through the perimeter adhesive.
- 7
Lift Off the Rear Cover
1 minGently lift the back cover off the chassis and set it aside.
- 8
Unscrew Lower Speaker Housing
2 minUse a Phillips #00 screwdriver to remove the screws securing the lower loudspeaker assembly cover to the frame.
- 9
Pry Up Speaker Housing
1 minInsert the flat end of a plastic spudger under the edge of the loudspeaker assembly and pry up to dislodge it.
- 10
Remove Old Loudspeaker Assembly
1 minLift the loudspeaker module out of the lower chassis cavity using tweezers or your fingers.
- 11
Position New Loudspeaker
1 minAlign the replacement loudspeaker module with the lower frame recess, making sure contact pads face the correct direction.
- 12
Press Loudspeaker into Frame
1 minGently press the speaker module into the housing until it snaps flush into position.
- 13
Fasten Housing Screws
2 minReinsert and tighten the Phillips #00 screws to secure the loudspeaker assembly to the phone chassis.
- 14
Clean Adhesive Residue
2 minApply a small amount of isopropyl alcohol to a cloth and wipe away old adhesive residue from the frame and rear cover edges.
- 15
Apply New Rear Adhesive
2 minLay pre-cut adhesive strips along the perimeter of the frame and peel off the protective backing.
- 16
Reattach Rear Cover
2 minAlign the back cover with the frame edges and press down firmly along all sides to seat the adhesive.
- 17
Reinsert SIM Tray
1 minPush the SIM card tray back into its slot on the left side of the device until it sits flush.
After your Motorola Moto G54 speaker repair
Power the Moto G54 back on and test the speaker repair function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Motorola Moto G54 job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Keep learning
Explore more Motorola Moto G54 repair context in the encyclopedia, or open related DIY guides.
