Phone · Motorola · Moto G52
Motorola Moto G52 Screen Replacement
Screen Replacement guide for the Motorola Moto G52
Before you begin
Tools
- Precision screwdriver set
- Plastic opening tools
- Suction cup
- Heat gun or hairdryer
- Tweezers
- Plastic spudger
- SIM eject tool
- Clean microfiber cloth
Parts / materials
- Motorola Moto G52 screen replacement
- Frame adhesive strips
- Back panel adhesive tape
- Isopropyl alcohol (90%+)
Safety
- Wear protective safety glasses when handling cracked screen glass.
- Always disconnect the battery before working near sensitive board components.
- Do not bend, pry, or puncture the lithium-ion battery with metal tools.
Overview
Step-by-step
- 1
Power Off Phone
1 minPress and hold the power button on the Moto G52, then select Power Off on the screen. Ensure the device is completely powered down before proceeding.
- 2
Remove SIM Tray
1 minInsert a SIM eject tool into the hole next to the SIM tray on the left edge. Push firmly to pop the tray out and remove it.
- 3
Heat Back Cover
2 minUse a heat gun or hairdryer on medium heat to warm the edges of the plastic back cover for about two minutes. This softens the internal adhesive holding the cover.
- 4
Apply Suction Cup
1 minPress a suction cup firmly onto the lower portion of the rear panel. Pull upward gently to create a slight gap between the back cover and the frame.
- 5
Insert Opening Pick
2 minSlide a plastic opening pick into the seam created near the bottom edge. Keep the pick shallow to avoid damaging internal flex cables.
- 6
Slice Back Panel Adhesive
4 minSlide the pick carefully around all four edges of the back cover to cut through the perimeter adhesive. Apply extra heat if the pick meets heavy resistance.
- 7
Remove Rear Panel
2 minGently lift the back cover off the chassis and place it aside. Take care not to snag any remaining adhesive.
- 8
Unscrew Midframe Fasteners
3 minUse a Phillips #00 screwdriver to remove all visible screws securing the plastic midframe shield. Keep the screws organized for reassembly.
- 9
Unclip Plastic Midframe
2 minInsert a spudger around the perimeter clips of the plastic midframe. Pop the clips open and remove the frame shield from the phone.
- 10
Disconnect Battery Flex Cable
1 minUse a plastic spudger to pry the battery connector straight up from the motherboard. Disconnecting the battery prevents electrical shorts during repair.
- 11
Disconnect Display Flex Cable
1 minLocate the display ribbon cable attached to the lower motherboard section. Pry the connector up carefully using your spudger.
- 12
Soften Battery Adhesive
2 minApply mild heat from a hair dryer to the back of the battery compartment for one minute. Alternatively, drop a small amount of high-concentration isopropyl alcohol along the battery edges.
- 13
Remove Battery
3 minPull the clear battery adhesive tab upward firmly, or slide a flat plastic card underneath to lever the battery free. Do not use metal tools that could puncture the cell.
- 14
Heat Front Screen
3 minApply heat evenly across the front display panel for two to three minutes to soften the glue holding the screen to the frame.
- 15
Separate Broken Screen
4 minAttach a suction cup near the top of the display and pull up to insert an opening pick along the seam. Carefully slide the pick around the screen border to loosen the display.
- 16
Remove Display Assembly
2 minLift the damaged display off the frame while carefully threading its flex cable through the slot in the midframe. Dispose of the old screen safely.
- 17
Clean Frame Channel
3 minScrape away lingering glass shards and old adhesive tape using tweezers and a plastic spudger. Wipe the rim with isopropyl alcohol to ensure new adhesive sticks properly.
- 18
Apply Screen Adhesive
3 minLay down pre-cut double-sided adhesive strips along the entire perimeter ledge of the inner frame. Peel off the protective film backing.
- 19
Thread Flex Cable
2 minTake the replacement screen and carefully feed its attached flex cable through the frame slot from the front.
- 20
Seat New Screen
2 minAlign the top edge of the replacement screen with the frame and press it into position. Lightly squeeze around the perimeter to adhere the glass.
- 21
Reinstall Battery
1 minPlace the battery back into its housing recess and press down firmly to secure it against the adhesive.
- 22
Reconnect Flex Cables
2 minPress the display flex cable and the battery cable connectors directly onto their sockets until they click into place.
- 23
Attach Midframe Shield
3 minSnap the plastic midframe back over the motherboard and tighten all saved Phillips #00 screws firmly.
- 24
Reattach Back Cover
3 minApply fresh double-sided adhesive along the inner back cover rim, then align and press the back panel down firmly onto the chassis.
After your Motorola Moto G52 screen replacement
Power the Moto G52 back on and test the screen replacement function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Motorola Moto G52 job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Keep learning
Explore more Motorola Moto G52 repair context in the encyclopedia, or open related DIY guides.
