Phone · Motorola · Moto G34
Motorola Moto G34 Screen Replacement
Screen Replacement guide for the Motorola Moto G34
Before you begin
Tools
- Heat gun or hairdryer
- Plastic opening picks
- Suction cup
- Phillips #00 screwdriver
- Precision tweezers
- Plastic spudger
- SIM eject tool
Parts / materials
- Replacement Moto G34 screen assembly
- Display frame adhesive strips
- Back cover adhesive tape
- 90%+ Isopropyl alcohol
Safety
- Wear eye protection to prevent glass fragments from causing injury during screen removal.
- Disconnect the battery flex cable immediately after opening to eliminate electrical short risks.
- Keep heat gun temperatures below 80°C to avoid damaging internal battery cells.
Overview
Step-by-step
- 1
Eject SIM Tray
1 minInsert a SIM eject tool into the small hole on the left edge of the phone to pop out the SIM card tray.
- 2
Heat Back Cover
2 minApply heat evenly around the outer edges of the back cover for 2 minutes to soften the adhesive.
- 3
Attach Suction Cup
1 minPlace a suction cup on the lower portion of the back panel and pull up gently to create a small gap.
- 4
Slice Back Cover Adhesive
4 minInsert a plastic opening pick into the gap and slide it along all four edges to cut through the perimeter glue.
- 5
Lift Off Back Cover
2 minGently hinge the back cover open from the right side, taking care not to strain the internal flex cables.
- 6
Disconnect Fingerprint Sensor
1 minUse a plastic spudger to pry up the fingerprint reader flex cable connector from the motherboard.
- 7
Remove Frame Screws
3 minUnscrew the 14 Phillips screws securing the upper motherboard shield and the lower speaker housing.
- 8
Unclip Motherboard Cover
2 minPry up and remove the plastic motherboard protective cover using a spudger.
- 9
Remove Speaker Module
1 minLift the loudspeaker assembly away from the bottom of the phone housing.
- 10
Disconnect Battery Cable
1 minPry the battery press connector directly up off the motherboard to cut power to the device.
- 11
Disconnect Display Flex Cable
1 minUse your plastic spudger to disconnect the main display flex cable from the lower section of the motherboard.
- 12
Heat Screen Assembly
3 minApply heat across the front glass frame with a heat gun for 3 minutes to loosen the screen adhesive.
- 13
Slice Display Adhesive
4 minPress an opening pick into the gap between the display glass and frame bezel, running it along the edges.
- 14
Remove Old Screen
2 minLift the broken screen off the frame, carefully feeding the attached flex ribbon cable out through the slot.
- 15
Clean Frame Channel
5 minScrape away remaining adhesive and micro-glass shards from the frame channel using tweezers and isopropyl alcohol.
- 16
Apply Display Adhesive
3 minLay pre-cut double-sided adhesive tape along the top, bottom, and side bezels of the phone frame.
- 17
Install New Screen
2 minThread the new display flex cable through the frame cutout and press the screen flat into the adhesive frame.
- 18
Reconnect Cables and Test
3 minAttach the display flex cable and battery cable, then power on the phone briefly to check touch sensitivity.
- 19
Reinstall Plastic Covers
3 minSet the motherboard cover and speaker module back into position, then drive in all 14 Phillips screws.
- 20
Reseal Back Panel
3 minReconnect the fingerprint flex cable, apply fresh rear adhesive, and firmly press the back cover onto the chassis.
After your Motorola Moto G34 screen replacement
Power the Moto G34 back on and test the screen replacement function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Motorola Moto G34 job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Keep learning
Explore more Motorola Moto G34 repair context in the encyclopedia, or open related DIY guides.
