Phone · Motorola · Moto G32
Motorola Moto G32 Speaker Repair
Speaker Repair guide for the Motorola Moto G32
Before you begin
Tools
- Heat gun or hair dryer
- Suction cup tool
- Plastic opening picks
- Spudger tool
- Phillips #00 screwdriver
- Tweezers
- SIM eject tool
Parts / materials
- Replacement Moto G32 loudspeaker module
- Pre-cut back cover adhesive tape
- Isopropyl alcohol (90%+)
Safety
- Power off the device completely before using any tools inside the housing.
- Do not overheat the rear cover to prevent battery damage or plastic warping.
- Wear safety glasses when working with prying tools and heated plastic components.
Overview
Step-by-step
- 1
Power Off the Phone
1 minPress and hold the power button until the power options appear, then select power off. Ensure the device is fully shut down before proceeding.
- 2
Eject the SIM Tray
1 minInsert a SIM eject tool into the small pinhole next to the card tray. Press firmly to pop the tray out, then slide it completely out of the phone.
- 3
Heat the Rear Cover
2 minApply heat to the outer edges of the rear plastic cover using a heat gun or hair dryer for about two minutes. This softens the adhesive holding the back cover.
- 4
Attach a Suction Cup
1 minPlace a suction cup onto the lower portion of the rear cover and press down to seal it. Gently pull upward on the suction ring to create a slight gap along the bottom edge.
- 5
Insert an Opening Pick
2 minInsert a thin plastic opening pick into the gap between the rear cover and the frame. Do not insert the pick further than a few millimeters to avoid damaging internal components.
- 6
Slice the Perimeter Adhesive
3 minSlide the plastic pick carefully around all four edges of the back panel to separate the adhesive. Apply additional heat if you feel resistance.
- 7
Remove the Rear Cover
1 minCarefully lift the rear cover off the phone frame once all adhesive has been separated. Set the back panel aside on a clean surface.
- 8
Unscrew the Loudspeaker Housing
2 minUse a Phillips #00 screwdriver to remove the screws securing the plastic lower speaker housing to the frame. Keep track of all removed screws.
- 9
Pry Up the Loudspeaker Module
2 minInsert the flat end of a plastic spudger beneath the edge of the loudspeaker module. Gently pry upward to unclip the assembly from the frame.
- 10
Remove the Faulty Loudspeaker
1 minLift the loudspeaker housing completely out of the bottom chassis. Clean away any dust or loose debris from the exposed daughterboard area.
- 11
Position the New Loudspeaker
2 minAlign the replacement Moto G32 loudspeaker module over the lower compartment. Press down evenly until it snaps flush into place against the contact pads.
- 12
Secure the Module Screws
2 minThread and tighten the Phillips #00 screws back into the loudspeaker housing. Avoid overtightening to prevent stripping the plastic threads.
- 13
Apply New Rear Adhesive
3 minPeel away old glue remnants with tweezers and isopropyl alcohol. Place new pre-cut adhesive strips along the perimeter of the phone frame.
- 14
Reseal the Rear Cover
2 minAlign the rear cover with the frame and press it down firmly. Apply heat for 30 seconds and press the edges again to ensure a solid bond.
- 15
Reinsert the SIM Tray
1 minSlide the SIM card tray back into its slot until it sits flush with the frame. Power on the phone to test the new speaker.
After your Motorola Moto G32 speaker repair
Power the Moto G32 back on and test the speaker repair function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Motorola Moto G32 job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Keep learning
Explore more Motorola Moto G32 repair context in the encyclopedia, or open related DIY guides.
