Phone · Motorola · Moto G24
Motorola Moto G24 Speaker Repair
Speaker Repair guide for the Motorola Moto G24
Before you begin
Tools
- Phillips #000 Precision Screwdriver
- Plastic prying tools
- Suction cup tool
- Heat gun or hair dryer
- Tweezers
- Spudger tool
- SIM ejector tool
Parts / materials
- Replacement Moto G24 loudspeaker
- Precut back cover adhesive strips
- High-concentration isopropyl alcohol (90%+)
Safety
- Power off the device completely before beginning disassembly to prevent electrical shorts.
- Do not overheat the rear panel; keep heat sources below 80°C to avoid damaging internal components.
- Wear safety glasses when working with heated adhesives and prying plastic panels.
Overview
Step-by-step
- 1
Power Off the Device
1 minPress and hold the Power button, then tap Power Off on the screen to completely shut down your Moto G24.
- 2
Eject the SIM Card Tray
1 minInsert a SIM ejector tool into the hole next to the SIM tray on the left edge and push gently to pop it out.
- 3
Heat the Back Cover
3 minApply warmth to the rear panel edges using a heat gun or hair dryer on low heat for two minutes to soften the adhesive.
- 4
Attach Suction Cup
1 minPress a suction cup firmly onto the lower portion of the rear panel, near the bottom edge.
- 5
Create an Opening Seam
2 minPull up gently on the suction cup and insert a thin plastic opening tool into the gap between the rear cover and the frame.
- 6
Slice the Edge Adhesive
3 minSlide the plastic pick carefully along the perimeter of the phone to cut through the perimeter adhesive sealant.
- 7
Detach the Back Cover
2 minLift the rear cover away from the chassis and set it aside in a clean location.
- 8
Remove Loudspeaker Screws
2 minUse a Phillips #000 screwdriver to remove all visible screws securing the bottom speaker assembly.
- 9
Pry Up the Speaker Assembly
2 minInsert a spudger under the notch of the loudspeaker housing and gently pry it up from the sub-board frame.
- 10
Lift Out the Damaged Speaker
1 minUse tweezers to carefully lift the old loudspeaker unit completely out of the phone body.
- 11
Clean the Contact Pins
2 minLightly brush the exposed spring contact pads on the sub-board with isopropyl alcohol to ensure proper electrical connection.
- 12
Place the New Loudspeaker
2 minAlign the replacement speaker assembly into the lower recess and press it down flush into position.
- 13
Secure Speaker Screws
2 minReinstall and tighten the Phillips #000 screws evenly to firm up the speaker housing against the frame.
- 14
Clean Frame Adhesive
3 minScrape away remaining old adhesive from the frame and back cover using a spudger and isopropyl alcohol.
- 15
Apply New Cover Adhesive
3 minPeel and lay down fresh precut adhesive strips around the inner rim of the phone's rear frame.
- 16
Reinstall the Back Cover
2 minAlign the rear cover properly over the chassis and press firmly around all edges to seal it tightly.
- 17
Reinsert SIM Card Tray
1 minSlide the SIM tray back into its slot on the side of the device until it sits flush.
After your Motorola Moto G24 speaker repair
Power the Moto G24 back on and test the speaker repair function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Motorola Moto G24 job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Keep learning
Explore more Motorola Moto G24 repair context in the encyclopedia, or open related DIY guides.
