Phone · Motorola · Moto G200 5G
Motorola Moto G200 5G Logic Board Repair
Logic Board Repair guide for the Motorola Moto G200 5G
Before you begin
Tools
- Phillips #000 screwdriver
- Heat gun or hair dryer
- Suction cup tool
- Plastic opening picks
- Spudger tool
- Tweezers
- SIM eject tool
Parts / materials
- Pre-cut back cover adhesive
- Isopropyl alcohol (99%)
- Thermal grease
Safety
- Wear safety glasses to protect eyes from potential glass or plastic fragments.
- Disconnect the battery press connector immediately after opening the device to prevent electrical shorts.
- Use only plastic non-conductive tools near exposed circuit components.
Overview
Step-by-step
- 1
Power Off the Phone
1 minPress and hold the power button, then tap Power Off on the screen. Confirm the device is fully shut down before proceeding.
- 2
Eject the SIM Card Tray
1 minInsert a SIM eject tool into the hole beside the SIM tray at the bottom edge. Press firmly to eject the tray and remove it.
- 3
Heat the Rear Cover
2 minApply a heat gun or hairdryer on low heat around the edges of the back cover for 2 minutes to soften the adhesive.
- 4
Attach Suction Cup
1 minPress a suction cup firmly onto the lower third of the rear panel. Pull gently upward to create a slight gap along the bottom seam.
- 5
Slice Rear Panel Adhesive
3 minInsert a plastic opening pick into the gap created by the suction cup. Slide the pick along all four edges to slice through the perimeter adhesive.
- 6
Lift Off the Back Cover
1 minCarefully lift the rear cover clear of the phone frame. Set the back cover aside in a clean location.
- 7
Remove Upper Bracket Screws
2 minUse a Phillips #000 screwdriver to remove the screws securing the plastic motherboard shield.
- 8
Detach Motherboard Shield
1 minInsert a plastic spudger under the edge of the upper plastic cover and lift it off the device.
- 9
Disconnect the Battery Cable
1 minUse a plastic spudger to pry the battery press-fit connector straight up from the motherboard to cut power.
- 10
Disconnect Display Interconnect Cable
1 minPry up the display flex cable connector from the motherboard using the flat end of a spudger.
- 11
Unplug Sub-Board Interconnect Flex
1 minDisconnect the main lower ribbon cable from its socket on the bottom portion of the logic board.
- 12
Disconnect Antenna Coaxial Cables
2 minUse fine tweezers or a spudger to carefully pop the antenna cable heads straight up off the logic board.
- 13
Disconnect Rear Camera Cables
2 minUnplug the rear camera press-fit connectors from the top left section of the logic board.
- 14
Disconnect Front Camera
1 minPry the front selfie camera connector off the motherboard and remove the camera module if loose.
- 15
Remove Logic Board Retaining Screw
1 minUnscrew the single Phillips screw securing the logic board to the internal chassis.
- 16
Lift Out the Logic Board
2 minGently lever a spudger beneath the bottom edge of the motherboard and lift the logic board out of the phone.
After your Motorola Moto G200 5G logic board repair
Power the Moto G200 5G back on and test the logic board repair function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Motorola Moto G200 5G job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Keep learning
Explore more Motorola Moto G200 5G repair context in the encyclopedia, or open related DIY guides.
