Phone · Motorola · Moto G200 5G
Motorola Moto G200 5G Charging Port Repair
Charging Port Repair guide for the Motorola Moto G200 5G
Before you begin
Tools
- Heat gun or hair dryer
- Suction cup tool
- Plastic prying tools
- Precision screwdriver set (Phillips #000)
- Spudger tool
- Tweezers
- SIM eject tool
Parts / materials
- Replacement Moto G200 5G charging board
- Back cover adhesive tape
- Isopropyl alcohol (90%+)
- Microfiber cloth
Safety
- Wear eye protection when using a heat gun near glass or plastic.
- Disconnect the battery before touching internal circuit components.
- Never puncture, crush, or bend the lithium-ion battery.
- Keep metallic tools away from battery terminals to prevent short circuits.
Overview
Step-by-step
- 1
Power off the phone
1 minPress and hold the Power button, then select Power Off on screen.
- 2
Eject the SIM tray
1 minInsert a SIM eject tool into the hole next to the tray on the side of the frame and pull the tray out.
- 3
Heat the back cover
2 minApply a heat gun or hair dryer set to low around the perimeter of the back panel for about 2 minutes to soften the glue.
- 4
Attach the suction cup
1 minPlace a suction cup on the lower third of the back cover and pull upward gently to create a small gap.
- 5
Insert a plastic prying tool
1 minPush an opening pick or plastic prying tool into the tiny gap between the back panel and the frame.
- 6
Slice through perimeter adhesive
3 minSlide the prying tool carefully along all four edges to cut the internal adhesive strips.
- 7
Remove the rear panel
1 minLift the rear panel completely off the chassis and set it aside on your workspace.
- 8
Unscrew lower speaker cover
2 minUse a Phillips #000 screwdriver to remove all screws holding down the lower speaker shield.
- 9
Remove the speaker module
1 minInsert a spudger under the edge of the speaker module and pry it up to uncover the charging board.
- 10
Unscrew upper motherboard cover
2 minRemove the Phillips screws securing the top motherboard bracket.
- 11
Remove upper motherboard bracket
1 minLift off the upper metal/plastic protective shield to gain access to the battery connector.
- 12
Disconnect the battery
1 minUse the flat end of a plastic spudger to detach the battery ribbon cable from the main board.
- 13
Disconnect main flex cable
1 minPry up the interboard flex connector from the charging sub-board at the bottom of the phone.
- 14
Disconnect antenna coaxial cable
1 minUse fine tweezers to gently lift the round antenna cable connector straight up off the sub-board.
- 15
Unfasten sub-board screws
1 minRemove any remaining Phillips screws securing the charging sub-board to the phone frame.
- 16
Remove the damaged charging board
2 minPry gently beneath the charging board with a spudger to release it from the frame recess.
- 17
Insert the replacement sub-board
1 minPosition the new charging board into the lower frame cutout and press down until seated properly.
- 18
Secure sub-board screws
1 minReinstall and tighten the small Phillips screws anchoring the sub-board.
- 19
Reconnect antenna cable
2 minAlign the antenna cable head over its socket on the new sub-board and press down until it snaps in.
- 20
Attach main flex cable
1 minSnap the main interconnect flex connector firmly back onto the sub-board header.
- 21
Reconnect battery press-connector
1 minPress the battery connector back onto its mainboard header until securely seated.
- 22
Reinstall motherboard bracket
2 minFit the top shield back over the mainboard and tighten its retaining Phillips screws.
- 23
Reinstall speaker module
2 minSet the speaker housing into place over the sub-board and fasten all corresponding Phillips screws.
- 24
Apply back cover adhesive
2 minLay down fresh adhesive strips along the outer ledge of the rear phone housing.
- 25
Reattach back cover
2 minAlign the back panel properly and press firmly along all edges to bond the adhesive.
After your Motorola Moto G200 5G charging port repair
Power the Moto G200 5G back on and test the charging port repair function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Motorola Moto G200 5G job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Keep learning
Explore more Motorola Moto G200 5G repair context in the encyclopedia, or open related DIY guides.
