Skip to main content

Phone · Motorola · Moto G15

Motorola Moto G15 Charging Port Repair

Charging Port Repair guide for the Motorola Moto G15

Moderate
~44 min
24 steps

Before you begin

Tools

  • Phillips #000 screwdriver
  • Heat gun or hair dryer
  • Suction cup tool
  • Plastic prying tools
  • Spudger tool
  • Tweezers
  • SIM eject tool

Parts / materials

  • Motorola Moto G15 replacement charging port board
  • Pre-cut back cover adhesive strips
  • Isopropyl alcohol (99%)

Safety

  • Disconnect the battery before servicing internal cables to prevent short circuits.
  • Do not bend or puncture the lithium-ion battery.
  • Use caution with heat tools to avoid burning skin or melting plastic frame components.

Overview

# Motorola Moto G15 Charging Port Repair Repair Guide Action-specific charging port repair walkthrough for the Motorola Moto G15. About 44 minutes across 24 steps. This DIY guide walks through charging port repair on the Motorola Moto G15 (Moto G series phone). Before you open the device, confirm the exact model number on the Motorola settings screen or rear housing so your replacement part matches the Moto G15 specifically—not a similar Moto G sibling. Most DIY techs finish this Motorola Moto G15 charging port repair in about 44 minutes when parts and tools are ready. Difficulty is rated intermediate for this model. Recommended tools for this Motorola Moto G15 job: Phillips #000 screwdriver, Heat gun or hair dryer, Suction cup tool, Plastic prying tools, Spudger tool, Tweezers, SIM eject tool. Parts and supplies: Motorola Moto G15 replacement charging port board, Pre-cut back cover adhesive strips, Isopropyl alcohol (99%). Power the Moto G15 off completely, remove SIMs/SD cards if present, and work on a clean, well-lit surface with a magnetic mat for screws. If a step feels wrong for your Motorola Moto G15, stop and compare the connector layout to the photos in this guide. When you prefer a same-day pro repair in Seattle instead, LML Repair can handle charging port repair for this model with tested parts and a workmanship warranty.

Step-by-step

  1. 1

    Power Down Device

    1 min

    Press and hold the power button, then select Power Off on the screen.

  2. 2

    Eject SIM Tray

    1 min

    Insert a SIM eject tool into the hole on the left edge of the phone to remove the SIM card tray.

  3. 3

    Heat Back Cover

    2 min

    Use a heat gun on low setting to heat the edges of the back cover for two minutes to soften the adhesive.

  4. 4

    Attach Suction Cup

    1 min

    Press a suction cup firmly onto the lower section of the back cover near the USB-C port.

  5. 5

    Insert Opening Pick

    2 min

    Pull up gently on the suction cup and insert a thin plastic opening pick into the gap between the frame and back cover.

  6. 6

    Slice Back Cover Adhesive

    4 min

    Slide the plastic pick carefully around all four edges of the back cover to cut through the remaining adhesive.

  7. 7

    Remove Back Cover

    1 min

    Lift the rear cover straight up and off the phone frame.

  8. 8

    Unscrew Lower Frame Screws

    3 min

    Use a Phillips #000 screwdriver to remove the screws securing the bottom loudspeaker assembly.

  9. 9

    Pry Off Loudspeaker Module

    2 min

    Insert the flat end of a spudger under the loudspeaker assembly and lift it out of the housing.

  10. 10

    Disconnect Battery Flex Cable

    1 min

    Pry up the battery press connector on the mainboard using a plastic spudger to safely cut power.

  11. 11

    Disconnect Interconnect Cable

    2 min

    Use a spudger to gently pop off the main interconnect flex cable connector from the charging port daughterboard.

  12. 12

    Disconnect Antenna Cables

    2 min

    Use precision tweezers to lift and disconnect the coaxial antenna cables attached to the charging board.

  13. 13

    Remove Daughterboard Screw

    1 min

    Remove the single Phillips screw holding the charging port board to the inner frame.

  14. 14

    Remove Charging Port Board

    2 min

    Pry under the edge of the charging port board with a spudger and remove it from the device.

  15. 15

    Position New Charging Board

    2 min

    Align the replacement charging port board into the lower recess of the phone frame.

  16. 16

    Secure Board Screw

    1 min

    Reinstall the Phillips screw to fix the new daughterboard securely to the frame.

  17. 17

    Reconnect Antenna Cables

    2 min

    Snap the coaxial antenna cables back onto their respective terminals on the new board using tweezers.

  18. 18

    Reconnect Interconnect Cable

    2 min

    Align and press down on the main interconnect flex cable connector until it clicks into place.

  19. 19

    Reconnect Battery Flex Cable

    1 min

    Press the battery cable connector back onto its mainboard socket.

  20. 20

    Reinstall Loudspeaker Module

    2 min

    Set the loudspeaker housing back into place over the charging board assembly.

  21. 21

    Secure Loudspeaker Screws

    3 min

    Drive the Phillips #000 screws back into the lower frame to secure the loudspeaker.

  22. 22

    Apply Back Cover Adhesive

    3 min

    Place pre-cut adhesive strips along the inner border of the rear housing.

  23. 23

    Reattach Back Cover

    2 min

    Align the back cover with the frame and press down firmly around the edges to seal.

  24. 24

    Reinsert SIM Tray

    1 min

    Push the SIM card tray back into its slot on the left edge until flush.

After your Motorola Moto G15 charging port repair

Power the Moto G15 back on and test the charging port repair function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Motorola Moto G15 job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.

Keep learning

Explore more Motorola Moto G15 repair context in the encyclopedia, or open related DIY guides.

logo_footer

Stay in the loop

Get new guides, reviews, and repair news.

© 2026 LML Repair. All rights reserved.