Step-by-step

1. 1

   Power Off Phone

   1 min

   Press and hold the power button, then tap Power Off on the screen. Ensure the device is fully shut down before proceeding.

2. 2

   Eject SIM Tray

   1 min

   Insert a SIM eject tool into the hole next to the tray. Press firmly to pop the tray out and remove it.

3. 3

   Heat Back Cover

   3 min

   Apply a heat gun set to low warmth along the back cover edges for two minutes. This softens the factory perimeter adhesive.

4. 4

   Attach Suction Cup

   2 min

   Place a suction cup on the lower third of the rear panel. Pull upward gently to create a slight gap between the panel and frame.

5. 5

   Insert Opening Pick

   2 min

   Slide a thin plastic pick into the gap created by the suction cup. Leave the pick in place to prevent the adhesive from resealing.

6. 6

   Slice Rear Adhesive

   5 min

   Slide the plastic pick around all four edges of the back panel. Carefully cut through all underlying glue strips.

7. 7

   Lift Off Back Cover

   2 min

   Gently lift the back panel away from the chassis. Set the panel aside on a clean work surface.

8. 8

   Unscrew Midframe Assembly

   4 min

   Use a precision Phillips screwdriver to remove all visible screws securing the midframe housing. Store the screws systematically.

9. 9

   Unclip Plastic Midframe

   3 min

   Insert a spudger around the perimeter clips of the midframe. Pry gently to unhook and remove the midframe.

10. 10

    Disconnect Battery Cable

    2 min

    Locate the battery connector on the motherboard. Pry it straight up using a nylon spudger to cut electrical power.

11. 11

    Disconnect Display Connector

    2 min

    Use the flat end of a spudger to detach the screen FPC cable from its motherboard socket.

12. 12

    Heat Front Display

    3 min

    Warm the entire front glass edge using a heat gun for two to three minutes. Maintain an even distance to prevent panel discoloration.

13. 13

    Slice Screen Glue

    6 min

    Press a suction cup onto the screen, pull up, and slide a pick under the glass edge. Carefully run the pick around the frame.

14. 14

    Separate Damaged Screen

    3 min

    Lift the display off the frame while carefully guiding its flex cable through the chassis slot. Discard the broken screen.

15. 15

    Clean Frame Bezel

    5 min

    Scrape away old adhesive and glass fragments using flat plastic tools. Wipe down the inner bezel with isopropyl alcohol.

16. 16

    Apply Screen Adhesive

    4 min

    Lay down fresh, pre-cut adhesive strips along the entire inner rim of the phone frame. Press down firmly to stick.

17. 17

    Thread Flex Cable

    2 min

    Pass the flex cable of the new screen through the frame slot. Align the new glass panel over the frame.

18. 18

    Seat New Screen

    3 min

    Press the screen into the frame gently, applying uniform pressure along all edges. Ensure the glass sits completely flush.

19. 19

    Reconnect Display Cable

    2 min

    Align and press down on the screen flex connector until it snaps securely onto the motherboard.

20. 20

    Reconnect Battery Cable

    1 min

    Snap the battery connector back into its motherboard terminal.

21. 21

    Reinstall Midframe Housing

    4 min

    Position the midframe over the motherboard and press down to engage clips. Reinsert and tighten all Phillips screws.

22. 22

    Reseal Back Cover

    3 min

    Apply new rear adhesive to the perimeter, then press the back cover onto the phone body firmly.

23. 23

    Reinsert SIM Tray

    1 min

    Slide the SIM tray back into the side slot until it sits flush with the frame.