Phone · Motorola · Moto G10 Power
Motorola Moto G10 Power Screen Replacement
Screen Replacement guide for the Motorola Moto G10 Power
Before you begin
Tools
- Phillips PH00 precision screwdriver
- Plastic opening picks
- Spudger
- Suction cup
- Heat gun or hairdryer
- Tweezers
- SIM eject tool
- Anti-static wrist strap
Parts / materials
- Replacement Moto G10 Power display assembly
- Pre-cut display adhesive strips
- 91% Isopropyl alcohol
- Lint-free cleaning wipes
Safety
- Wear protective eyewear to guard against flying glass fragments when removing broken screen.
- Disconnect the battery cable immediately after opening the device to reduce electrical hazards.
- Avoid using sharp metal tools directly against the lithium battery.
- Do not overheat the device beyond 80°C to prevent internal component damage.
Overview
Step-by-step
- 1
Power off the phone
1 minPress and hold the power button, then tap Power Off on the screen. Ensure the device is completely powered down before starting.
- 2
Eject the SIM tray
1 minInsert a SIM eject tool into the pinhole on the left edge of the phone. Push firmly to pop the tray out, then remove it.
- 3
Heat the rear cover edges
2 minApply heat around the rear cover perimeter with a heat gun on low for 2 minutes. This softens internal adhesive and clip pressure.
- 4
Unclip the back cover
3 minInsert a plastic opening pick into the seam near the SIM slot. Slide along the perimeter to release the plastic clips securing the cover.
- 5
Disconnect the fingerprint reader flex
2 minGently lift the rear cover slightly without straining the ribbon cable. Use tweezers to pop off the fingerprint sensor connector from the board.
- 6
Remove motherboard shield screws
3 minUnscrew the Phillips screws securing the plastic motherboard bracket. Keep track of screws for reassembly.
- 7
Remove motherboard shield cover
1 minPry up the motherboard bracket using a spudger and lift it out of the phone chassis.
- 8
Disconnect the battery connector
1 minUse a plastic spudger to disconnect the battery flex cable from the motherboard. This prevents short circuits during screen replacement.
- 9
Remove loudspeaker screws
2 minRemove the Phillips screws holding the lower speaker module in place at the bottom of the device.
- 10
Remove the loudspeaker module
1 minInsert a plastic opening tool under the loudspeaker edge and lift it out of the housing.
- 11
Disconnect display ribbon cable
1 minPry up the display flex cable press-connector located on the lower sub-board or motherboard.
- 12
Heat the front glass display
3 minHeat the front glass edges with a heat gun for 3 minutes to soften the display adhesive bond.
- 13
Slice perimeter screen adhesive
4 minPress a suction cup onto the screen and pull upward while sliding an opening pick under the glass edge to slice through adhesive.
- 14
Remove broken screen assembly
2 minLift the screen away from the body while threading the flex cable out through the frame slot.
- 15
Clean frame glue and glass
5 minScrape away remaining glue and glass shards from the frame ledge using tweezers and isopropyl alcohol wipes.
- 16
Apply new frame adhesive
3 minPlace new pre-cut adhesive strips along the inner perimeter frame of the phone chassis.
- 17
Set the replacement screen
3 minThread the new screen flex cable through the frame slot and align the display evenly into the housing.
- 18
Reconnect display and battery flexes
2 minPress the display flex cable onto its terminal until it snaps, then reattach the main battery connector.
- 19
Reinstall covers and back panel
4 minReattach the motherboard and speaker covers with their screws, reconnect the fingerprint sensor, and snap the back cover shut.
After your Motorola Moto G10 Power screen replacement
Power the Moto G10 Power back on and test the screen replacement function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Motorola Moto G10 Power job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Keep learning
Explore more Motorola Moto G10 Power repair context in the encyclopedia, or open related DIY guides.
