Phone · Motorola · Moto G Stylus 5G 2025
Motorola Moto G Stylus 5G 2025 Screen Replacement
Screen Replacement guide for the Motorola Moto G Stylus 5G 2025
Before you begin
Tools
- Heat gun or hairdryer
- Plastic opening tools
- Suction cup
- Precision Phillips #00 screwdriver
- Tweezers
- Anti-static wrist strap
- SIM eject tool
Parts / materials
- Replacement screen assembly
- Display adhesive strips
- Back panel adhesive
- Isopropyl alcohol (99%)
Safety
- Wear safety glasses to protect against flying glass shards.
- Disconnect the battery before handling internal hardware.
- Do not overheat the phone to avoid lithium-ion battery damage.
Overview
Step-by-step
- 1
Remove the stylus pen
1 minPress the stylus top to pop it out, then pull the pen completely from the bottom slot.
- 2
Eject the SIM tray
1 minInsert a SIM eject tool into the hole on the side to pop out and remove the SIM tray.
- 3
Heat the rear cover
2 minApply heat around the edges of the rear panel using a heat gun for 2 minutes to soften the glue.
- 4
Attach suction cup
1 minPlace a suction cup near the bottom edge of the back panel and pull upward gently.
- 5
Insert opening pick
2 minSlide a thin plastic opening pick into the gap created between the frame and the rear cover.
- 6
Slice rear adhesive
3 minSlide the plastic pick carefully around all four edges to cut through the adhesive seal.
- 7
Lift off back panel
1 minCarefully separate and lift the back panel off the chassis.
- 8
Unscrew midframe panel
3 minRemove the Phillips #00 screws securing the plastic midframe shield to the body.
- 9
Pry off midframe shield
2 minInsert an opening tool under the edge of the midframe and snap it free from the phone frame.
- 10
Disconnect battery cable
1 minUse a plastic spudger to pry the battery press-fit connector straight up from the motherboard.
- 11
Disconnect display cable
1 minPry up the display flex cable connector located on the motherboard.
- 12
Heat front glass
3 minApply heat across the perimeter of the display screen for 2 to 3 minutes.
- 13
Attach suction to front screen
1 minPress a suction cup firmly onto the lower portion of the front screen.
- 14
Slice screen adhesive
4 minWork an opening pick around all perimeter edges of the front glass to slice through display adhesive.
- 15
Remove broken display
2 minThread the display flex cable out of the frame slot and remove the old screen assembly.
- 16
Clean frame edges
4 minScrape residual adhesive and glass bits off the frame using tweezers and isopropyl alcohol.
- 17
Apply display adhesive
3 minPlace pre-cut adhesive strips along the inner border of the phone frame.
- 18
Install new screen
3 minGuide the flex cable through the frame slot and press the new screen level into the frame.
- 19
Reconnect display flex
1 minPress the display cable connector firmly into its motherboard socket until it snaps in.
- 20
Reconnect battery flex
1 minAlign and press down the battery flex connector onto the motherboard.
- 21
Reattach midframe shield
3 minSnap the midframe cover into place and secure it with the Phillips screws.
- 22
Reseal back panel
2 minApply new adhesive to the frame perimeter and press the rear cover back into position.
- 23
Reinsert SIM and stylus
1 minPush the SIM tray and stylus pen back into their original slots.
After your Motorola Moto G Stylus 5G 2025 screen replacement
Power the Moto G Stylus 5G 2025 back on and test the screen replacement function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Motorola Moto G Stylus 5G 2025 job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Keep learning
Explore more Motorola Moto G Stylus 5G 2025 repair context in the encyclopedia, or open related DIY guides.
