Phone · Motorola · Moto G Stylus 5G 2025
Motorola Moto G Stylus 5G 2025 Logic Board Repair
Logic Board Repair guide for the Motorola Moto G Stylus 5G 2025
Before you begin
Tools
- Precision screwdriver set (Phillips #000)
- Plastic prying tools
- Suction cup tool
- Heat gun or hair dryer
- Tweezers
- Spudger tool
- SIM eject tool
Parts / materials
- Replacement logic board for Moto G Stylus 5G 2025
- Pre-cut back panel adhesive strips
- 99% Isopropyl alcohol
Safety
- Disconnect the battery immediately after removing the midframe bracket to prevent electrical short circuits.
- Wear safety eye protection when heating and working near glass components.
- Use an anti-static wrist strap to protect sensitive IC components from electrostatic discharge.
- Power off the device completely before starting disassembly.
Overview
Step-by-step
- 1
Remove the SIM card tray
1 minInsert a SIM eject tool into the hole next to the tray on the side of the phone to eject it. Remove the tray completely.
- 2
Remove the integrated stylus
1 minPush inward on the bottom of the stylus until it clicks, then pull it out from its slot.
- 3
Heat the rear panel
2 minApply a heat gun evenly across the outer edges of the back cover for 2 minutes to soften the adhesive.
- 4
Attach a suction cup
1 minPlace a suction cup on the lower portion of the rear panel and lift firmly to create a small gap.
- 5
Insert an opening pick
2 minPush a plastic opening pick into the gap between the rear glass cover and the midframe.
- 6
Slice the perimeter adhesive
3 minSlide the pick carefully around all four edges of the phone to separate the back cover from the frame.
- 7
Remove the rear panel
1 minLift the rear cover straight up and off the phone frame, taking care not to snag any adhesive remnants.
- 8
Unscrew the upper motherboard bracket
3 minUse a Phillips #000 screwdriver to remove all screws securing the top protective plastic cover.
- 9
Pry up the motherboard bracket
2 minInsert the flat end of a spudger under the plastic bracket edge and lift it out of the chassis.
- 10
Disconnect the battery cable
1 minPry the battery press connector straight up from its socket using a plastic spudger to cut power.
- 11
Disconnect the display and interconnect cables
2 minUnplug the main interconnect flex cable and display connectors from the top logic board using a spudger.
- 12
Disconnect antenna coaxial cables
2 minUse precision tweezers to unclip the antenna cables attached near the edge of the logic board.
- 13
Remove the rear camera modules
2 minUnplug the camera connectors from the motherboard and lift the camera sensors out of their recessed housings.
- 14
Remove logic board mounting screws
2 minRemove the remaining Phillips screws locking the logic board to the aluminum internal frame.
- 15
Lift out the damaged logic board
2 minGently pry up from the bottom edge of the logic board and lift it out of the frame.
- 16
Position the new logic board
2 minAlign the replacement logic board over the guide pins in the chassis and press it gently into place.
After your Motorola Moto G Stylus 5G 2025 logic board repair
Power the Moto G Stylus 5G 2025 back on and test the logic board repair function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Motorola Moto G Stylus 5G 2025 job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Keep learning
Explore more Motorola Moto G Stylus 5G 2025 repair context in the encyclopedia, or open related DIY guides.
