Phone · Motorola · Moto G Power 5G 2024
Motorola Moto G Power 5G 2024 Logic Board Repair
Logic Board Repair guide for the Motorola Moto G Power 5G 2024
Before you begin
Tools
- Precision screwdriver set (Phillips #000)
- Plastic prying tools
- Suction cup tool
- Heat gun or hair dryer
- Tweezers
- Spudger tool
- SIM eject tool
- Anti-static wrist strap
Parts / materials
- Pre-cut back cover adhesive sticker
- Isopropyl alcohol (99%)
- Microfiber cleaning cloth
Safety
- Wear an anti-static wrist strap connected to a grounded surface to protect components from ESD.
- Avoid using sharp metal tools directly near the lithium-ion battery to prevent punctures.
- Wear safety glasses when heating panels in case of cracked plastic or glass.
Overview
Step-by-step
- 1
Power Down the Device
1 minPress and hold the power button, then select Power Off on the screen. Ensure the device is fully shut down before proceeding.
- 2
Eject the SIM Tray
1 minInsert a SIM eject tool into the pinhole on the left edge of the phone. Push firmly inward to release and pull out the SIM card tray.
- 3
Heat the Rear Cover
3 minApply heat evenly around the outer edges of the back panel for 2 to 3 minutes using a heat gun or hair dryer to soften the adhesive.
- 4
Slice the Rear Adhesive
4 minAttach a suction cup to the lower back cover, pull up to create a small gap, and insert a plastic opening pick. Slide the pick around all four edges to slice the adhesive.
- 5
Remove the Back Cover
1 minCarefully lift the back cover off the chassis and set it aside on a clean work surface.
- 6
Unscrew the Upper Midframe
3 minUse a Phillips #000 screwdriver to remove all visible screws securing the plastic upper midframe shield.
- 7
Detach the Upper Midframe
2 minInsert a spudger under the edge of the plastic upper midframe and gently pry it up to remove it from the frame.
- 8
Disconnect the Battery Cable
1 minPry the battery press-connector straight up off its socket on the logic board using a flat-edge spudger.
- 9
Disconnect Main Flex Cables
2 minDisconnect the display flex cable and the interconnect ribbon cable from the top logic board using a plastic spudger.
- 10
Disconnect Antenna Coaxial Cables
2 minUse precision tweezers to pry up and disconnect the coaxial antenna cables attached to the logic board.
- 11
Remove Camera Modules
3 minUnplug the front selfie camera and main rear camera flex connectors, then lift the camera modules out of their housings.
- 12
Remove Logic Board Screw
1 minUnscrew the single Phillips #000 screw holding the motherboard anchored to the internal frame.
- 13
Lift Out the Logic Board
2 minCarefully lever a spudger under the edge of the logic board and lift it out of the phone body.
- 14
Position the New Logic Board
3 minLower the replacement logic board into place, making sure no cables or connectors are trapped beneath it.
- 15
Secure and Reassemble
5 minReconnect all camera modules, flex cables, antenna wires, and battery before reattaching the midframe and sealing the back cover with fresh adhesive.
After your Motorola Moto G Power 5G 2024 logic board repair
Power the Moto G Power 5G 2024 back on and test the logic board repair function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Motorola Moto G Power 5G 2024 job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Keep learning
Explore more Motorola Moto G Power 5G 2024 repair context in the encyclopedia, or open related DIY guides.
