Skip to main content

Phone · Motorola · Moto G 5G Plus

Power Button Repair Guide for Moto G 5G Plus

Power Button Repair guide for the Motorola Moto G 5G Plus

Moderate
~28 min
18 steps

Before you begin

Tools

  • Heat gun or hair dryer
  • Suction cup tool
  • Plastic prying tools
  • Opening picks
  • Precision screwdriver set (Phillips #000)
  • Spudger tool
  • Tweezers
  • SIM eject tool

Parts / materials

  • Replacement Moto G 5G Plus power button flex cable
  • High-concentration isopropyl alcohol (90%+)
  • Pre-cut back cover adhesive tape
  • Cotton swabs

Safety

  • Always disconnect the battery cable before handling internal hardware components to avoid short circuits.
  • Do not overheat the rear panel, as excessive heat can damage the battery and internal screen components.
  • Wear an anti-static wrist strap during internal component handling to avoid electrostatic discharge.

Overview

# Power Button Repair Guide for Moto G 5G Plus Action-specific power button repair walkthrough for the Motorola Moto G 5G Plus. About 28 minutes across 18 steps. This DIY guide walks through power button repair on the Motorola Moto G 5G Plus (Moto G series phone). Before you open the device, confirm the exact model number on the Motorola settings screen or rear housing so your replacement part matches the Moto G 5G Plus specifically—not a similar Moto G sibling. Most DIY techs finish this Motorola Moto G 5G Plus power button repair in about 28 minutes when parts and tools are ready. Difficulty is rated intermediate for this model. Recommended tools for this Motorola Moto G 5G Plus job: Heat gun or hair dryer, Suction cup tool, Plastic prying tools, Opening picks, Precision screwdriver set (Phillips #000), Spudger tool, Tweezers, SIM eject tool. Parts and supplies: Replacement Moto G 5G Plus power button flex cable, High-concentration isopropyl alcohol (90%+), Pre-cut back cover adhesive tape, Cotton swabs. Power the Moto G 5G Plus off completely, remove SIMs/SD cards if present, and work on a clean, well-lit surface with a magnetic mat for screws. If a step feels wrong for your Motorola Moto G 5G Plus, stop and compare the connector layout to the photos in this guide. When you prefer a same-day pro repair in Seattle instead, LML Repair can handle power button repair for this model with tested parts and a workmanship warranty.

Step-by-step

  1. 1

    Power off the phone

    1 min

    Press and hold the power button, then select Shut Down. Ensure the device is completely powered off before proceeding.

  2. 2

    Eject the SIM card tray

    1 min

    Insert a SIM eject tool into the small hole on the left side of the phone. Push firmly to eject the tray and set it aside.

  3. 3

    Heat the back cover

    2 min

    Apply a heat gun or hairdryer around the edges of the back panel for approximately two minutes to soften the rear adhesive.

  4. 4

    Apply the suction cup

    1 min

    Place a suction cup near the bottom edge of the back cover and pull upward gently to create a tiny gap.

  5. 5

    Slice the rear adhesive

    3 min

    Insert a plastic opening pick into the gap and slowly slide it along the perimeter to slice through the adhesive seal.

  6. 6

    Remove the back cover

    1 min

    Lift the rear plastic cover straight off the frame and set it aside carefully.

  7. 7

    Unscrew the upper motherboard bracket

    3 min

    Use a Phillips #000 screwdriver to remove all visible screws securing the top plastic housing cover.

  8. 8

    Remove the motherboard cover

    1 min

    Use a plastic spudger to carefully lift and detach the plastic motherboard shield from the top of the phone.

  9. 9

    Disconnect the battery flex cable

    1 min

    Pry the battery connector directly up from its socket on the motherboard using a plastic spudger to cut power.

  10. 10

    Disconnect the power button cable

    1 min

    Locate the power button and fingerprint sensor flex cable connector on the motherboard and pop it open with a spudger.

  11. 11

    Pry out the damaged power button cable

    2 min

    Use tweezers to carefully peel the flex cable and power button switch out of its channel inside the side frame.

  12. 12

    Clean the side frame slot

    2 min

    Dampen a cotton swab with high-concentration isopropyl alcohol and clean off any leftover adhesive in the power button recess.

  13. 13

    Install the new power button flex cable

    2 min

    Remove the protective backing from the new flex cable adhesive and press the switch firmly into the side frame slot.

  14. 14

    Reconnect the power button cable

    1 min

    Align and snap the power button flex connector back onto its socket on the motherboard.

  15. 15

    Reconnect the battery cable

    1 min

    Press the battery cable connector straight down onto its motherboard terminal until it clicks into place.

  16. 16

    Reinstall the motherboard cover

    2 min

    Place the top plastic shield back over the motherboard and secure it using the Phillips screws.

  17. 17

    Reattach the back cover

    2 min

    Apply new pre-cut adhesive tape around the frame perimeter, then press the back cover firmly onto the phone.

  18. 18

    Reinsert the SIM card tray

    1 min

    Align the SIM card tray with its slot and push it in until it sits flush against the frame.

After your Motorola Moto G 5G Plus power button repair

Power the Moto G 5G Plus back on and test the power button repair function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Motorola Moto G 5G Plus job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.

Keep learning

Explore more Motorola Moto G 5G Plus repair context in the encyclopedia, or open related DIY guides.

logo_footer

Stay in the loop

Get new guides, reviews, and repair news.

© 2026 LML Repair. All rights reserved.