Phone · Motorola · G75 5G
Motorola G75 5G Screen Replacement
Screen Replacement guide for the Motorola G75 5G
Before you begin
Tools
- Phillips #000 screwdriver
- Heat gun or hair dryer
- Suction cup tool
- Plastic opening picks
- Spudger tool
- SIM eject tool
- Tweezers
- Isopropyl alcohol (99%)
Parts / materials
- Replacement Motorola G75 5G screen assembly
- B-7000 frame adhesive
- Pre-cut back cover adhesive strips
Safety
- Wear protective safety glasses to shield your eyes from flying glass fragments when removing a shattered screen.
- Disconnect the battery cable immediately after opening the device to prevent electrical short circuits.
- Handle the lithium-ion battery with care to avoid punctures or sharp bends.
Overview
Step-by-step
- 1
Eject the SIM card tray
1 minInsert a SIM eject tool into the hole next to the SIM tray. Press firmly until the tray pops out, then remove it completely.
- 2
Heat the back panel
2 minUse a heat gun or hair dryer to heat the outer edges of the back cover for two minutes to soften the underlying adhesive.
- 3
Attach the suction cup
1 minPress a suction cup firmly onto the lower portion of the rear panel, near the bottom edge.
- 4
Slice the back panel adhesive
3 minPull up on the suction cup to create a small gap, insert an opening pick, and slide it around all four edges to slice through the adhesive.
- 5
Remove the back panel
1 minLift the back cover away from the phone body and place it on a clean surface.
- 6
Unscrew the midframe housing
3 minUse a Phillips #000 screwdriver to remove all visible screws securing the upper motherboard bracket and lower speaker assembly.
- 7
Pry off the plastic midframe
2 minInsert a plastic spudger into the notch on the side of the midframe cover and gently lever it up to unclip it from the chassis.
- 8
Disconnect the battery press connector
1 minUse the edge of a plastic spudger to pry the battery flex connector straight up from its motherboard socket to kill power to the device.
- 9
Disconnect the main screen flex cable
1 minLocate the main display flex connector on the motherboard and disconnect it using your spudger.
- 10
Disconnect the daughterboard interconnect cable
1 minUnplug the secondary interconnect flex cable spanning between the motherboard and bottom sub-board.
- 11
Heat the front display panel
3 minApply heat to the front screen edges for three minutes to loosen the display adhesive holding the screen to the frame.
- 12
Separate the screen from the frame
4 minPlace a suction cup on the glass, pull upward to insert an opening pick between the screen bezel and frame, and slice through the adhesive perimeter.
- 13
Thread the screen flex through the frame
2 minLift the damaged display off the frame while carefully guiding the attached ribbon cable through the slot in the midframe.
- 14
Clean adhesive residue from the frame
3 minScrape away remaining glue from the internal housing rim with a plastic tool and wipe clean using isopropyl alcohol.
- 15
Test the replacement display
4 minThread the new screen's cable through the frame, connect it to the motherboard along with the battery, and power on the phone to check touch and display function.
- 16
Adhere the new screen to the frame
3 minDisconnect the battery, apply new screen adhesive tape or B-7000 glue around the frame border, and press the new screen firmly into place.
After your Motorola G75 5G screen replacement
Power the G75 5G back on and test the screen replacement function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Motorola G75 5G job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Keep learning
Explore more Motorola G75 5G repair context in the encyclopedia, or open related DIY guides.
