Phone · Motorola · G62 5G
Motorola G62 5G Speaker Repair
Speaker Repair guide for the Motorola G62 5G
Before you begin
Tools
- Phillips #00 screwdriver
- Plastic opening picks
- Suction handle
- Tweezers
- Spudger
- SIM eject tool
- Heat gun or iOpener
Parts / materials
- Replacement Motorola G62 5G loudspeaker module
- Pre-cut back cover adhesive
- 90%+ isopropyl alcohol
Safety
- Wear safety glasses to protect against potential glass splinters.
- Always disconnect the battery connector before touching internal electronics.
- Do not overheat the device perimeter past 80°C to avoid damaging internal hardware.
Overview
Step-by-step
- 1
Turn off the phone
1 minPress and hold the power button, then select Power Off on the screen. Ensure the device is fully shut down before proceeding.
- 2
Remove SIM tray
1 minInsert a SIM eject tool into the hole next to the SIM card tray on the side of the phone. Push firmly until the tray pops out, then remove it.
- 3
Warm the back cover
2 minApply a heated iOpener or hair dryer around the perimeter of the back cover for 2 minutes to soften the adhesive.
- 4
Insert opening pick
2 minAttach a suction cup near the bottom edge of the back panel, pull up gently, and insert a plastic opening pick beneath the seam.
- 5
Slice back cover adhesive
3 minSlide the plastic pick carefully along all four sides of the phone to cut through the perimeter adhesive sealant.
- 6
Detach rear back panel
2 minLift the rear cover away from the chassis. Clean off residual adhesive around the frame using isopropyl alcohol.
- 7
Remove bottom bracket screws
3 minUse a Phillips #00 screwdriver to remove the screws securing the lower loudspeaker cover to the frame.
- 8
Disconnect the battery cable
2 minUse a plastic spudger to pry up the motherboard cover and disconnect the battery press-connector for safe servicing.
- 9
Pry up loudspeaker housing
2 minInsert the flat end of a spudger under the notch of the loudspeaker housing and gently lever it up from the lower frame.
- 10
Remove bad speaker unit
2 minUse fine-tip tweezers to gently lift the speaker module out of its recessed channel on the lower board assembly.
- 11
Seat new speaker unit
2 minPlace the new replacement speaker into the designated recess, ensuring metal contact pins align correctly with the sub-board pads.
- 12
Snap loudspeaker housing in place
2 minAlign the lower speaker cover over the bottom frame and press down firmly until the plastic clips snap shut.
- 13
Reconnect the battery cable
1 minAlign the battery flex connector over its terminal socket and press down firmly until it clicks into place.
- 14
Reinstall bottom bracket screws
3 minThread and tighten the Phillips screws into the lower loudspeaker housing until snug.
- 15
Apply back cover adhesive
3 minLay fresh pre-cut adhesive strips along the phone's outer perimeter and peel away the protective film backing.
- 16
Reattach the rear panel
2 minAlign the back cover with the frame and press firmly around all edges to bond the cover securely.
- 17
Reinsert the SIM card tray
1 minPush the SIM card tray back into its slot on the side of the device until it sits flush.
After your Motorola G62 5G speaker repair
Power the G62 5G back on and test the speaker repair function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Motorola G62 5G job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Keep learning
Explore more Motorola G62 5G repair context in the encyclopedia, or open related DIY guides.
