Phone · Motorola · G62 5G
Motorola G62 5G Charging Port Repair
Charging Port Repair guide for the Motorola G62 5G
Before you begin
Tools
- Precision screwdriver set (Phillips #000)
- Plastic prying tools
- Suction cup tool
- Heat gun or hair dryer
- Tweezers
- Spudger tool
Parts / materials
- Replacement Motorola G62 5G charging port daughterboard
- Pre-cut back cover adhesive tape
- Isopropyl alcohol wipes
Safety
- Wear eye protection when heating and prying plastic panels.
- Do not bend or puncture the internal lithium battery while prying near components.
- Ensure the device is powered off completely before beginning internal disassembly.
Overview
Step-by-step
- 1
Power Off and Eject SIM Tray
1 minTurn off the phone completely. Insert a SIM eject tool into the hole on the left frame to pop out the SIM card tray.
- 2
Heat the Rear Cover
2 minApply heat from a heat gun or hair dryer to the outer edges of the back cover for 2 minutes to soften the adhesive.
- 3
Attach Suction Cup
1 minPlace a suction cup on the lower third of the back panel and gently pull upward to create a small seam.
- 4
Insert Plastic Pick
1 minPush a thin plastic prying tool or opening pick into the seam created beneath the rear panel.
- 5
Slice Rear Panel Adhesive
3 minSlide the plastic pick carefully around all four edges of the back cover to cut through the perimeter adhesive.
- 6
Remove Rear Cover
1 minLift the rear plastic panel off the internal frame and place it on a clean surface.
- 7
Unscrew Lower Loudspeaker Cover
2 minUse a Phillips #000 screwdriver to remove the screws holding the bottom loudspeaker assembly to the frame.
- 8
Pry Up Loudspeaker Module
1 minInsert a spudger beneath the edge of the loudspeaker module and lever it out of the chassis.
- 9
Disconnect Interconnect Flex Cable
1 minUse the flat end of a spudger to pop open the press connector for the main flex cable on the daughterboard.
- 10
Disconnect Antenna Cable
1 minGently pry up the round coaxial antenna connector from the daughterboard using fine tweezers.
- 11
Remove Daughterboard Retaining Screw
1 minUnscrew the single Phillips #000 screw securing the charging port daughterboard to the inner housing.
- 12
Lift Out Old Charging Board
1 minPry gently beneath the edge of the old charging port board using a plastic tool and lift it out.
- 13
Position New Charging Board
1 minPlace the new charging port daughterboard directly into the bottom recess of the frame.
- 14
Fasten Daughterboard Screw
1 minInsert and tighten the single Phillips #000 screw to hold the daughterboard securely in place.
- 15
Reconnect Antenna Cable
1 minAlign the coaxial antenna head over its socket on the new board and snap it down gently with tweezers.
- 16
Attach Interconnect Flex Cable
1 minAlign the main flex connector over the board header and press firmly until it snaps into place.
- 17
Reinstall Loudspeaker Module
1 minFit the loudspeaker housing back into position over the daughterboard assembly.
- 18
Secure Loudspeaker Screws
2 minThread and tighten all Phillips #000 screws to hold the loudspeaker assembly flush.
- 19
Apply Frame Adhesive
3 minClean remaining glue with isopropyl alcohol and lay down strips of new double-sided adhesive along the frame.
- 20
Press Rear Cover Sealed
2 minAlign the back cover over the housing and press firmly along all edges to set the adhesive bond.
- 21
Reinsert SIM Card Tray
1 minSlide the SIM card tray back into the slot until it sits flush against the outer frame.
After your Motorola G62 5G charging port repair
Power the G62 5G back on and test the charging port repair function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Motorola G62 5G job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Keep learning
Explore more Motorola G62 5G repair context in the encyclopedia, or open related DIY guides.
