Skip to main content

Phone · Motorola · G51 5G

Motorola G51 5G Charging Port Repair

Charging Port Repair guide for the Motorola G51 5G

Moderate
~38 min
20 steps

Before you begin

Tools

  • Phillips #00 screwdriver
  • Heat gun or iOpener
  • Plastic opening picks
  • Spudger
  • Tweezers
  • SIM eject tool

Parts / materials

  • Replacement charging port board for Moto G51 5G
  • Back cover adhesive sticker or repair tape
  • High-concentration isopropyl alcohol (90%+)

Safety

  • Wear protective eye safety glasses when applying heat to the phone.
  • Use an anti-static wrist strap to prevent electrostatic discharge while working on internal electronics.
  • Work in a clean, ventilated area when handling adhesives and isopropyl alcohol.

Overview

# Motorola G51 5G Charging Port Repair Repair Guide Action-specific charging port repair walkthrough for the Motorola G51 5G. About 38 minutes across 20 steps. This DIY guide walks through charging port repair on the Motorola G51 5G (Moto G series phone). Before you open the device, confirm the exact model number on the Motorola settings screen or rear housing so your replacement part matches the G51 5G specifically—not a similar Moto G sibling. Most DIY techs finish this Motorola G51 5G charging port repair in about 38 minutes when parts and tools are ready. Difficulty is rated intermediate for this model. Recommended tools for this Motorola G51 5G job: Phillips #00 screwdriver, Heat gun or iOpener, Plastic opening picks, Spudger, Tweezers, SIM eject tool. Parts and supplies: Replacement charging port board for Moto G51 5G, Back cover adhesive sticker or repair tape, High-concentration isopropyl alcohol (90%+). Power the G51 5G off completely, remove SIMs/SD cards if present, and work on a clean, well-lit surface with a magnetic mat for screws. If a step feels wrong for your Motorola G51 5G, stop and compare the connector layout to the photos in this guide. When you prefer a same-day pro repair in Seattle instead, LML Repair can handle charging port repair for this model with tested parts and a workmanship warranty.

Step-by-step

  1. 1

    Turn Off the Phone

    1 min

    Press and hold the power button, then tap Power Off to shut down the device completely before starting.

  2. 2

    Remove the SIM Card Tray

    1 min

    Insert a SIM eject tool into the hole next to the card tray on the left side of the phone and push to release it.

  3. 3

    Heat the Back Cover

    3 min

    Apply heat around the edges of the plastic back cover using a heat gun or iOpener for 2 to 3 minutes to soften the internal adhesive.

  4. 4

    Slice the Back Cover Adhesive

    4 min

    Insert a plastic opening pick between the rear panel and frame, then slide it around the perimeter to cut through the adhesive.

  5. 5

    Disconnect the Fingerprint Sensor Cable

    2 min

    Slightly tilt open the back cover and use tweezers or a spudger to press off the fingerprint sensor cable connector from the motherboard.

  6. 6

    Remove the Back Cover

    1 min

    Lift the back cover away from the phone body and set it aside in a safe area.

  7. 7

    Remove the Lower Speaker Screws

    2 min

    Use a Phillips #00 screwdriver to remove the screws securing the lower loudspeaker housing.

  8. 8

    Lift Out the Loudspeaker Assembly

    2 min

    Insert a spudger under the edge of the loudspeaker unit and lever it up out of the phone frame.

  9. 9

    Disconnect the Main Interconnect Cable

    1 min

    Pry up the press connector of the main flex interconnect cable off the daughterboard using a plastic spudger.

  10. 10

    Unclip the Antenna Coaxial Cable

    2 min

    Use fine-tip tweezers to carefully lift and unclip the antenna coaxial cable connector from the charging board socket.

  11. 11

    Pry Up the Charging Port Board

    2 min

    Insert a flat opening tool under the edge of the charging port board and lift it out of the lower recessed frame.

  12. 12

    Position the New Charging Board

    2 min

    Align the replacement charging port board into the lower chassis slot and press it down until seated flat.

  13. 13

    Reattach the Antenna Coaxial Cable

    2 min

    Position the coaxial cable head over the sub-board socket and press gently until it snaps into place.

  14. 14

    Connect the Main Interconnect Cable

    1 min

    Align the main flex connector over the new board socket and press down firmly to secure the connection.

  15. 15

    Reinstall the Loudspeaker Assembly

    2 min

    Fit the loudspeaker cover back into the bottom of the frame over the daughterboard area.

  16. 16

    Secure the Speaker Screws

    2 min

    Drive the Phillips #00 screws back into the loudspeaker module until snug.

  17. 17

    Reconnect the Fingerprint Reader

    2 min

    Hold the rear panel near the frame and snap the fingerprint sensor flex cable back onto the motherboard connector.

  18. 18

    Apply New Back Cover Adhesive

    3 min

    Clean off old adhesive using isopropyl alcohol, then stick custom cut adhesive tape onto the frame edges.

  19. 19

    Seal the Back Cover

    2 min

    Align the back panel carefully over the phone chassis and press firmly along all edges to bond the adhesive.

  20. 20

    Reinsert the SIM Tray

    1 min

    Slide the SIM card tray back into its slot on the left edge of the device until it sits flush.

After your Motorola G51 5G charging port repair

Power the G51 5G back on and test the charging port repair function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Motorola G51 5G job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.

Keep learning

Explore more Motorola G51 5G repair context in the encyclopedia, or open related DIY guides.

logo_footer

Stay in the loop

Get new guides, reviews, and repair news.

© 2026 LML Repair. All rights reserved.