Skip to main content
logo

Phone · Motorola · G40 Fusion

Motorola G40 Fusion Screen Replacement

Screen Replacement guide for the Motorola G40 Fusion

Difficult
~39 min
18 steps

Before you begin

Tools

  • Heat gun or hair dryer
  • Phillips #00 screwdriver
  • Suction cup tool
  • Plastic prying tools
  • Spudger tool
  • Tweezers
  • SIM eject tool

Parts / materials

  • Replacement Motorola G40 Fusion screen assembly
  • Double-sided adhesive strips
  • Isopropanol cleaning wipes

Safety

  • Wear eye protection to prevent injury from flying glass fragments.
  • Disconnect the battery before handling internal electronics.
  • Do not puncture or bend the internal lithium-ion battery.

Overview

# Motorola G40 Fusion Screen Replacement Repair Guide Action-specific screen replacement walkthrough for the Motorola G40 Fusion. About 39 minutes across 18 steps. This DIY guide walks through screen replacement on the Motorola G40 Fusion (Moto G series phone). Before you open the device, confirm the exact model number on the Motorola settings screen or rear housing so your replacement part matches the G40 Fusion specifically—not a similar Moto G sibling. Most DIY techs finish this Motorola G40 Fusion screen replacement in about 39 minutes when parts and tools are ready. Difficulty is rated advanced for this model. Recommended tools for this Motorola G40 Fusion job: Heat gun or hair dryer, Phillips #00 screwdriver, Suction cup tool, Plastic prying tools, Spudger tool, Tweezers, SIM eject tool. Parts and supplies: Replacement Motorola G40 Fusion screen assembly, Double-sided adhesive strips, Isopropanol cleaning wipes. Power the G40 Fusion off completely, remove SIMs/SD cards if present, and work on a clean, well-lit surface with a magnetic mat for screws. If a step feels wrong for your Motorola G40 Fusion, stop and compare the connector layout to the photos in this guide. When you prefer a same-day pro repair in Seattle instead, LML Repair can handle screen replacement for this model with tested parts and a workmanship warranty.

Step-by-step

  1. 1

    Power Off Phone

    1 min

    Press and hold the power button, then select Shut Down on the screen.

  2. 2

    Eject SIM Card Tray

    1 min

    Insert a SIM eject pin into the tray hole on the left edge and pull out the tray.

  3. 3

    Heat Back Cover

    2 min

    Apply warmth to the rear cover edges with a heat gun for two minutes to soften adhesive.

  4. 4

    Insert Opening Pick

    2 min

    Attach a suction cup to the lower back plastic and pry open a slight gap using a thin pick.

  5. 5

    Slice Back Adhesive

    3 min

    Slide the pick around all perimeter edges to release the back cover clips and adhesive.

  6. 6

    Disconnect Fingerprint Sensor

    2 min

    Lift the rear cover gently and use a spudger to pop off the fingerprint flex connector.

  7. 7

    Unscrew Top Cover

    3 min

    Remove the Phillips #00 screws securing the plastic motherboard protective frame.

  8. 8

    Detach Top Shield

    2 min

    Pry up and remove the motherboard shield to expose the main board connections.

  9. 9

    Disconnect Battery Cable

    1 min

    Use a plastic spudger to pry the battery flex cable connector straight up from its socket.

  10. 10

    Unscrew Loudspeaker

    2 min

    Remove all Phillips #00 screws holding the lower loudspeaker module in place.

  11. 11

    Remove Loudspeaker

    1 min

    Lift the bottom speaker housing out of the frame and set it aside.

  12. 12

    Disconnect Screen Cable

    1 min

    Unplug the display flex cable press connector from the motherboard.

  13. 13

    Heat Front Display

    2 min

    Heat the front glass edges for two minutes to soften the display adhesive bond.

  14. 14

    Slice Screen Adhesive

    4 min

    Press a suction cup onto the glass and slice through the adhesive around all edges with an opening pick.

  15. 15

    Remove Damaged Screen

    2 min

    Lift the old display off the body while carefully feeding the flex cable through the frame slot.

  16. 16

    Clean Frame Ledge

    4 min

    Scrape away remaining glue and glass shards from the frame perimeter using a spudger.

  17. 17

    Apply New Adhesive

    3 min

    Lay fresh double-sided adhesive strips along the cleaned internal edges of the frame.

  18. 18

    Install New Display

    3 min

    Thread the new display cable through the slot, align the panel, and press firmly along the edges.

After your Motorola G40 Fusion screen replacement

Power the G40 Fusion back on and test the screen replacement function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Motorola G40 Fusion job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.

Keep learning

Explore more Motorola G40 Fusion repair context in the encyclopedia, or open related DIY guides.

Repair encyclopediaAll G40 Fusion guides
logo_footer

Stay in the loop

Get new guides, reviews, and repair news.

Quick Links

Explore

    © 2026 LML Repair. All rights reserved.