Skip to main content

Phone · Motorola · G4 Plus

Motorola G4 Plus Charging Port Repair

Charging Port Repair guide for the Motorola G4 Plus

Moderate
~68 min
23 steps

Before you begin

Tools

  • Phillips #00 Screwdriver
  • Plastic Spudger
  • Plastic Opening Pick
  • Tweezers
  • Soldering Iron
  • Desoldering Braid
  • Magnifying Glass
  • Anti-static Wrist Strap

Parts / materials

  • Replacement Moto G4 Plus Micro-USB Charging Port
  • Solder Wire
  • Liquid Rosin Flux
  • 90%+ Isopropyl Alcohol

Safety

  • Wear safety glasses while soldering to protect against flux splatter.
  • Perform soldering in a well-ventilated space or use a fume extractor.
  • Always disconnect the battery before handling motherboard components.

Overview

# Motorola G4 Plus Charging Port Repair Repair Guide Action-specific charging port repair walkthrough for the Motorola G4 Plus. About 68 minutes across 23 steps. This DIY guide walks through charging port repair on the Motorola G4 Plus (Moto G series phone). Before you open the device, confirm the exact model number on the Motorola settings screen or rear housing so your replacement part matches the G4 Plus specifically—not a similar Moto G sibling. Most DIY techs finish this Motorola G4 Plus charging port repair in about 68 minutes when parts and tools are ready. Difficulty is rated intermediate for this model. Recommended tools for this Motorola G4 Plus job: Phillips #00 Screwdriver, Plastic Spudger, Plastic Opening Pick, Tweezers, Soldering Iron, Desoldering Braid, Magnifying Glass, Anti-static Wrist Strap. Parts and supplies: Replacement Moto G4 Plus Micro-USB Charging Port, Solder Wire, Liquid Rosin Flux, 90%+ Isopropyl Alcohol. Power the G4 Plus off completely, remove SIMs/SD cards if present, and work on a clean, well-lit surface with a magnetic mat for screws. If a step feels wrong for your Motorola G4 Plus, stop and compare the connector layout to the photos in this guide. When you prefer a same-day pro repair in Seattle instead, LML Repair can handle charging port repair for this model with tested parts and a workmanship warranty.

Step-by-step

  1. 1

    Pop off back cover

    2 min

    Insert a plastic opening pick into the notch near the charging port and pry the rear cover away from the chassis.

  2. 2

    Remove SIM and SD cards

    1 min

    Slide out any installed SIM cards and MicroSD cards from their respective slots.

  3. 3

    Unscrew midframe fasteners

    5 min

    Remove the 19 Phillips #00 screws securing the inner midframe assembly to the phone body.

  4. 4

    Pry up midframe edges

    3 min

    Insert a plastic spudger along the outer seam of the midframe to unclip it from the housing.

  5. 5

    Disconnect fingerprint sensor flex

    2 min

    Gently lift the midframe and use tweezers to unlatch the fingerprint sensor flex cable connector.

  6. 6

    Remove midframe

    1 min

    Lift the midframe completely off the phone and place it on your workspace mat.

  7. 7

    Disconnect battery cable

    1 min

    Use a plastic spudger to pry the battery flex connector straight up from the motherboard.

  8. 8

    Remove battery

    3 min

    Insert a flat spudger under the battery and carefully lever it up to break the underlying adhesive.

  9. 9

    Disconnect display flex cable

    2 min

    Flip up the ZIF lock lever and pull the display flex cable out of its motherboard socket.

  10. 10

    Disconnect antenna cable

    1 min

    Use tweezers to unsnap the coaxial antenna cable connector from the bottom of the board.

  11. 11

    Remove camera modules

    3 min

    Disconnect and remove both the front-facing and rear camera modules from the motherboard.

  12. 12

    Remove motherboard

    2 min

    Carefully lift the motherboard out of the plastic frame.

  13. 13

    Apply flux to port pins

    2 min

    Apply a small drop of liquid flux over the damaged Micro-USB port's mounting pads and data pins.

  14. 14

    Desolder defective port

    8 min

    Heat the anchor pins and pin rows with a soldering iron while using desoldering braid to absorb solder.

  15. 15

    Clean motherboard contact pads

    2 min

    Clean the bare solder pads using isopropyl alcohol and a lint-free swab.

  16. 16

    Position new charging port

    2 min

    Align the replacement Micro-USB port precisely over the cleaned contact pads on the motherboard.

  17. 17

    Solder mounting anchors

    5 min

    Apply solder to the four main structural mounting legs to secure the port to the board.

  18. 18

    Solder data and power pins

    7 min

    Carefully solder each of the rear pin contacts using a fine-tip soldering iron and fresh flux.

  19. 19

    Inspect solder joints

    2 min

    Examine the pin connections under a magnifying glass to verify there are no solder bridges or loose pins.

  20. 20

    Reinstall motherboard and cameras

    3 min

    Place the motherboard back into the frame and reconnect the front and rear cameras.

  21. 21

    Reconnect flex cables and battery

    3 min

    Attach the display flex, antenna cable, and battery connector back onto the motherboard.

  22. 22

    Attach fingerprint flex and midframe

    3 min

    Reconnect the fingerprint sensor flex cable, snap the midframe onto the body, and press along the edges.

  23. 23

    Secure midframe screws

    5 min

    Reinstall and tighten all 19 Phillips #00 screws around the midframe, then reattach the back cover.

After your Motorola G4 Plus charging port repair

Power the G4 Plus back on and test the charging port repair function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Motorola G4 Plus job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.

Keep learning

Explore more Motorola G4 Plus repair context in the encyclopedia, or open related DIY guides.

logo_footer

Stay in the loop

Get new guides, reviews, and repair news.

© 2026 LML Repair. All rights reserved.