Skip to main content
logo

Phone · Motorola · G30

Motorola G30 Screen Replacement

Screen Replacement guide for the Motorola G30

Difficult
~48 min
20 steps

Before you begin

Tools

  • Heat gun or hair dryer
  • Suction cup tool
  • Plastic prying tools
  • Precision screwdriver set (Phillips #000)
  • Spudger tool
  • Tweezers
  • SIM eject tool

Parts / materials

  • Double-sided adhesive strips
  • Isopropyl alcohol (99%)
  • Clean microfiber cloth
  • Replacement screen assembly

Safety

  • Wear safety glasses to protect your eyes from fine glass splinters.
  • Do not puncture, bend, or apply excessive heat to the lithium-ion battery.
  • Operate in a well-ventilated area when using isopropyl alcohol.

Overview

# Motorola G30 Screen Replacement Repair Guide Action-specific screen replacement walkthrough for the Motorola G30. About 48 minutes across 20 steps. This DIY guide walks through screen replacement on the Motorola G30 (Moto G series phone). Before you open the device, confirm the exact model number on the Motorola settings screen or rear housing so your replacement part matches the G30 specifically—not a similar Moto G sibling. Most DIY techs finish this Motorola G30 screen replacement in about 48 minutes when parts and tools are ready. Difficulty is rated advanced for this model. Recommended tools for this Motorola G30 job: Heat gun or hair dryer, Suction cup tool, Plastic prying tools, Precision screwdriver set (Phillips #000), Spudger tool, Tweezers, SIM eject tool. Parts and supplies: Double-sided adhesive strips, Isopropyl alcohol (99%), Clean microfiber cloth, Replacement screen assembly. Power the G30 off completely, remove SIMs/SD cards if present, and work on a clean, well-lit surface with a magnetic mat for screws. If a step feels wrong for your Motorola G30, stop and compare the connector layout to the photos in this guide. When you prefer a same-day pro repair in Seattle instead, LML Repair can handle screen replacement for this model with tested parts and a workmanship warranty.

Step-by-step

  1. 1

    Turn Off and Eject SIM Tray

    2 min

    Power down your Moto G30 completely. Insert a SIM eject tool into the hole on the left edge and push gently to remove the tray.

  2. 2

    Heat Back Cover Edges

    2 min

    Apply a heat gun set to low along the rear panel edges for 2 minutes to soften the underlying adhesive.

  3. 3

    Attach Suction Cup and Pry Edge

    2 min

    Place a suction cup on the lower portion of the rear cover. Pull up firmly to create a gap, then slip a thin plastic opening pick into the seam.

  4. 4

    Slice Rear Cover Adhesive

    3 min

    Slide the pick around all four edges of the back cover to cut through the perimeter adhesive.

  5. 5

    Disconnect Fingerprint Sensor Cable

    2 min

    Gently tilt the rear cover up and use a plastic spudger to disconnect the fingerprint reader ribbon cable from the board.

  6. 6

    Remove Midframe Phillips Screws

    3 min

    Unscrew all Phillips #000 screws securing the plastic midframe to the phone frame.

  7. 7

    Unclip and Lift Off Midframe

    2 min

    Insert a spudger along the outer seam of the midframe to release plastic clips, then lift the midframe away.

  8. 8

    Disconnect Battery Flex Cable

    1 min

    Use the flat end of a spudger to pry the battery connector straight up off its motherboard socket.

  9. 9

    Disconnect Display Flex Cable

    1 min

    Pry up the main display ribbon connector located on the lower section of the motherboard.

  10. 10

    Heat Battery Area

    2 min

    Apply mild heat from a heat gun to the front display glass directly over the battery location for 1 minute.

  11. 11

    Pry Out Battery

    3 min

    Slide a flat plastic card under the battery to break the adhesive tabs, then carefully lift the battery out.

  12. 12

    Heat Front Screen Edges

    3 min

    Heat the perimeter of the cracked front screen for 2-3 minutes to loosen the factory adhesive.

  13. 13

    Separate Screen from Frame

    2 min

    Insert a thin prying pick between the plastic frame bezel and the front glass assembly.

  14. 14

    Remove Old Screen Assembly

    3 min

    Slice remaining adhesive along the edges, lift the screen off, and thread its flex cable out through the frame slot.

  15. 15

    Clean Frame Ledge

    4 min

    Scrape off residual adhesive and glass fragments from the inner frame using a spudger and isopropyl alcohol.

  16. 16

    Apply Screen Frame Adhesive

    3 min

    Lay down fresh double-sided adhesive tape along the perimeter shelf of the middle frame.

  17. 17

    Install New Display Assembly

    2 min

    Thread the replacement screen's ribbon cable through the frame slot and press the screen firmly into place.

  18. 18

    Reinstall and Connect Battery

    2 min

    Place the battery back into its housing, then snap the display flex cable and battery flex cable onto their sockets.

  19. 19

    Reattach Midframe and Screws

    3 min

    Snap the plastic midframe over the motherboard and secure it by reinserting all original Phillips screws.

  20. 20

    Connect Fingerprint Flex and Seal Back Cover

    3 min

    Reconnect the fingerprint sensor cable, apply adhesive strips to the rear perimeter, and press the back cover tightly down.

After your Motorola G30 screen replacement

Power the G30 back on and test the screen replacement function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Motorola G30 job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.

Keep learning

Explore more Motorola G30 repair context in the encyclopedia, or open related DIY guides.

Repair encyclopediaAll G30 guides
logo_footer

Stay in the loop

Get new guides, reviews, and repair news.

Quick Links

Explore

    © 2026 LML Repair. All rights reserved.