Skip to main content
logo

Phone · Motorola · G Pure

Motorola G Pure Microphone Repair

Microphone Repair guide for the Motorola G Pure

Moderate
~32 min
17 steps

Before you begin

Tools

  • Phillips #00 screwdriver
  • Plastic opening picks
  • Spudger
  • Tweezers
  • SIM eject tool
  • Anti-static wrist strap

Parts / materials

  • Replacement Motorola Moto G Pure sub-board with microphone

Safety

  • Power off the phone completely before starting the teardown.
  • Wear an anti-static wrist strap connected to a grounded surface to prevent electrostatic discharge.
  • Do not bend or puncture the battery while prying near internal components.

Overview

# Motorola G Pure Microphone Repair Repair Guide Action-specific microphone repair walkthrough for the Motorola G Pure. About 32 minutes across 17 steps. This DIY guide walks through microphone repair on the Motorola G Pure (Moto G series phone). Before you open the device, confirm the exact model number on the Motorola settings screen or rear housing so your replacement part matches the G Pure specifically—not a similar Moto G sibling. Most DIY techs finish this Motorola G Pure microphone repair in about 32 minutes when parts and tools are ready. Difficulty is rated intermediate for this model. Recommended tools for this Motorola G Pure job: Phillips #00 screwdriver, Plastic opening picks, Spudger, Tweezers, SIM eject tool, Anti-static wrist strap. Parts and supplies: Replacement Motorola Moto G Pure sub-board with microphone. Power the G Pure off completely, remove SIMs/SD cards if present, and work on a clean, well-lit surface with a magnetic mat for screws. If a step feels wrong for your Motorola G Pure, stop and compare the connector layout to the photos in this guide. When you prefer a same-day pro repair in Seattle instead, LML Repair can handle microphone repair for this model with tested parts and a workmanship warranty.

Step-by-step

  1. 1

    Eject the SIM Tray

    1 min

    Insert a SIM eject tool into the pinhole on the left side of the phone. Press firmly to eject the SIM tray and pull it completely out.

  2. 2

    Unclip the Back Cover

    4 min

    Insert a plastic opening pick into the seam between the back cover and screen frame near the SIM slot. Slide the pick around the perimeter to release the plastic clips.

  3. 3

    Disconnect the Fingerprint Cable

    2 min

    Slightly lift the back cover to locate the fingerprint reader flex cable. Use the flat end of a spudger to pry the connector straight up from the motherboard.

  4. 4

    Remove the Back Cover

    1 min

    Separate the back cover completely from the phone chassis and place it on a clean surface.

  5. 5

    Unscrew the Loudspeaker Module

    3 min

    Use a Phillips #00 screwdriver to remove the seven screws securing the bottom loudspeaker cover.

  6. 6

    Remove the Loudspeaker Module

    2 min

    Insert a spudger under the edge of the loudspeaker module and pry upward to remove it from the phone.

  7. 7

    Disconnect the Main Flex Cable

    1 min

    Use a plastic spudger to snap the main interconnect flex cable connector off the lower sub-board.

  8. 8

    Disconnect the Antenna Cable

    2 min

    Grasp the metal head of the coaxial antenna cable with tweezers and gently pry it straight up from the sub-board socket.

  9. 9

    Remove the Faulty Sub-Board

    2 min

    Insert a spudger beneath the lower sub-board containing the primary microphone and pry it up from the frame adhesive.

  10. 10

    Seat the New Sub-Board

    2 min

    Align the replacement sub-board with the housing pins in the lower frame and press down firmly to set it in place.

  11. 11

    Reconnect the Antenna Cable

    2 min

    Position the antenna coaxial connector over its board socket and gently press down until it clicks into place.

  12. 12

    Reconnect the Main Flex Cable

    1 min

    Align the main interconnect flex cable over the socket on the new sub-board and press down on one side, then the other, until it snaps in.

  13. 13

    Reposition the Loudspeaker Module

    1 min

    Place the loudspeaker module back over the sub-board, ensuring all screw alignment tabs match up.

  14. 14

    Secure the Loudspeaker Module

    3 min

    Replace and tighten the seven Phillips #00 screws holding the loudspeaker cover down.

  15. 15

    Reconnect the Fingerprint Sensor

    2 min

    Hold the back cover close to the chassis and snap the fingerprint sensor flex cable onto its motherboard socket.

  16. 16

    Snap On the Back Cover

    2 min

    Align the back cover with the frame and press around the entire border until all internal clips click shut.

  17. 17

    Reinsert the SIM Tray

    1 min

    Slide the SIM card tray back into the slot on the left edge of the phone until flush.

After your Motorola G Pure microphone repair

Power the G Pure back on and test the microphone repair function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Motorola G Pure job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.

Keep learning

Explore more Motorola G Pure repair context in the encyclopedia, or open related DIY guides.

Repair encyclopediaAll G Pure guides
logo_footer

Stay in the loop

Get new guides, reviews, and repair news.

Quick Links

Explore

    © 2026 LML Repair. All rights reserved.