Phone · Motorola · Moto Edge 60 Stylus
Motorola Moto Edge 60 Stylus Logic Board Repair
Logic Board Repair guide for the Motorola Moto Edge 60 Stylus
Before you begin
Tools
- Precision screwdriver set (Phillips #00)
- Heat gun or hair dryer
- Suction cup tool
- Plastic prying tools
- Tweezers
- Spudger tool
- Anti-static wrist strap
Parts / materials
- Replacement back cover adhesive
- Isopropyl alcohol (99%)
- Lint-free microfiber cloth
Safety
- Wear an anti-static wrist strap to protect delicate microchips from electrostatic discharge.
- Always disconnect the battery press connector before touching or removing any logic board components.
- Do not overheat the rear panel above 80°C to prevent warping plastic elements.
Overview
Step-by-step
- 1
Eject the SIM Tray
1 minInsert a SIM eject tool into the hole next to the SIM tray on the top edge of the phone. Push firmly until the tray pops out, then pull it completely free.
- 2
Remove the Stylus
1 minPress the spring-loaded end of the stylus on the bottom frame to unlatch it. Slide the stylus entirely out of its cavity.
- 3
Heat the Rear Cover
2 minUse a heat gun or hairdryer on medium setting to warm the perimeter of the back cover for 2 minutes. This softens the adhesive securing the back panel.
- 4
Apply Suction Cup
1 minPress a suction cup onto the lower portion of the rear panel. Pull upward gently to create a small gap between the glass and the frame.
- 5
Slice the Rear Adhesive
4 minInsert an opening pick into the gap created by the suction cup. Carefully slide the pick along all four edges to cut through the perimeter adhesive adhesive.
- 6
Remove the Rear Cover
1 minGently lift the back cover off the chassis. Set the back panel aside in a safe, dust-free area.
- 7
Unscrew the Upper Bracket
3 minUse a Phillips #00 screwdriver to remove the screws securing the upper motherboard plastic bracket.
- 8
Remove the Upper Bracket
2 minInsert a spudger under the edge of the motherboard bracket and pry upward to unclip it. Lift the bracket off the phone.
- 9
Disconnect the Battery
1 minUse the flat end of a plastic spudger to pop the battery press connector directly up from the logic board to prevent short circuits.
- 10
Disconnect the Display Cable
1 minPry the display flex cable press connector straight up off the socket on the mainboard using a spudger.
- 11
Disconnect the Interconnect Cable
1 minUnplug the lower interconnect flex connector that routes power and data from the sub-board to the main logic board.
- 12
Disconnect Coaxial Antennas
2 minUse precision tweezers to carefully lift the white and black antenna coaxial connectors straight up from the logic board.
- 13
Remove the Front Camera
2 minDisconnect the front-facing selfie camera flex cable, then use tweezers to lift the camera module out of its housing notch.
- 14
Remove the Motherboard Screws
1 minLocate and remove the single Phillips screw securing the logic board to the inner aluminum chassis.
- 15
Lift Out the Logic Board
2 minCarefully insert a plastic pry tool underneath the bottom edge of the logic board and lift it out of the phone frame.
- 16
Inspect the Board for Damage
5 minPlace the logic board under good lighting or a magnifying lens to inspect for burnt micro-components, corrosion, or fractured solder joints.
After your Motorola Moto Edge 60 Stylus logic board repair
Power the Moto Edge 60 Stylus back on and test the logic board repair function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Motorola Moto Edge 60 Stylus job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Keep learning
Explore more Motorola Moto Edge 60 Stylus repair context in the encyclopedia, or open related DIY guides.
