Phone · Motorola · Moto Edge 50 Ultra
Motorola Moto Edge 50 Ultra Charging Port Repair
Charging Port Repair guide for the Motorola Moto Edge 50 Ultra
Before you begin
Tools
- Heat gun or hair dryer
- Suction cup tool
- Plastic prying tools
- Precision screwdriver set (Phillips #000)
- Tweezers
- Spudger tool
- SIM eject tool
Parts / materials
- Replacement Moto Edge 50 Ultra charging port daughterboard
- Back cover adhesive strips
- Isopropyl alcohol (99%)
- Cleaning wipes
Safety
- Wear eye protection when heating glass or adhesive components.
- Ensure the device battery is discharged below 25% to minimize fire hazard during disassembly.
- Work in a well-ventilated space when utilizing isopropyl alcohol and adhesives.
Overview
Step-by-step
- 1
Power Off and Remove SIM Tray
2 minTurn off the Motorola Moto Edge 50 Ultra completely. Insert a SIM eject tool into the tray hole at the bottom frame and remove the SIM card tray.
- 2
Heat the Back Cover Edges
3 minUse a heat gun or hair dryer to warm the perimeter of the back cover for 2 to 3 minutes. This softens the factory adhesive securing the rear panel.
- 3
Attach Suction Cup
2 minPress a heavy-duty suction cup onto the lower portion of the rear panel. Pull gently upward to create a thin gap between the back cover and the frame.
- 4
Slice Back Panel Adhesive
5 minInsert a thin plastic opening pick into the gap created by the suction cup. Carefully slide the pick along the perimeter to slice through all rear cover adhesive.
- 5
Remove the Back Cover
2 minLift the rear cover straight off the chassis once all adhesive is cut. Set the back cover aside in a safe, dust-free location.
- 6
Unscrew the Lower Speaker Assembly
4 minLocate the Phillips #000 screws securing the lower speaker cover over the daughterboard. Remove all screws and keep them organized by size.
- 7
Remove the Speaker Assembly
2 minInsert a spudger under the edge of the speaker enclosure. Carefully pry upward to unclip and remove the speaker cover from the frame.
- 8
Disconnect the Interconnect Cable
2 minUse the flat end of a plastic spudger to pry straight up on the main flex ribbon connector attached to the sub-board. Do not bend the flex cable excessively.
- 9
Disconnect Antenna Cables
3 minUse precision tweezers to unsnap the coaxial antenna connectors from the charging port daughterboard. Pull straight up from the board socket to avoid damaging the pins.
- 10
Remove Daughterboard Screws
2 minIdentify any remaining Phillips screws anchoring the charging port daughterboard to the bottom frame. Remove them with a Phillips #000 driver.
- 11
Pry Up the Charging Port Daughterboard
3 minGently insert a spudger under the daughterboard and lift it out from its recess. Be mindful of the USB-C port rubber gasket fitted into the outer frame.
- 12
Clean the Sub-Board Recess
3 minInspect the lower frame cavity and USB-C opening for lint, dust, or residual adhesive. Wipe the housing clean with a tiny amount of isopropyl alcohol on a cotton swab.
- 13
Set New Daughterboard into Place
3 minAlign the replacement charging port daughterboard over the bottom frame recess. Press down gently until it sits flush against the chassis.
- 14
Secure the Daughterboard Screws
2 minThread and tighten the Phillips screws to lock the new daughterboard firmly into the chassis.
- 15
Reconnect Antenna Cables
3 minPosition the coaxial antenna cable heads directly over their corresponding board sockets. Press firmly down until you feel a clean snap.
- 16
Reconnect the Interconnect Cable
2 minAlign the main flex cable connector over the daughterboard socket. Press down firmly on one side, then the other, until it clicks into place.
- 17
Position the Speaker Assembly
2 minPlace the lower speaker cover back over the daughterboard assembly. Press along the edges to engage the plastic retaining clips.
- 18
Secure the Speaker Assembly Screws
4 minReinstall all saved Phillips #000 screws to secure the speaker cover and internal shield.
- 19
Test Charging Functionality
3 minPlug a USB-C charger into the port temporarily to confirm the screen shows charging status. Unplug the charger before proceeding with final assembly.
- 20
Clean Remaining Adhesive
5 minScrape away old adhesive traces from both the rear phone frame and the underside of the back cover using isopropyl alcohol.
- 21
Apply Back Cover Adhesive
4 minApply custom pre-cut adhesive strips or a thin line of frame sealant around the inner ledge of the rear housing.
- 22
Press Back Cover into Frame
3 minAlign the back cover over the phone frame and press firmly around all four edges to seal the device.
- 23
Reinsert the SIM Tray
1 minSlide the SIM card and tray back into its slot at the bottom of the frame until flush.
After your Motorola Moto Edge 50 Ultra charging port repair
Power the Moto Edge 50 Ultra back on and test the charging port repair function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Motorola Moto Edge 50 Ultra job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.
Keep learning
Explore more Motorola Moto Edge 50 Ultra repair context in the encyclopedia, or open related DIY guides.
