Skip to main content

Phone · Motorola · Moto Edge 50 Pro

Motorola Moto Edge 50 Pro Charging Port Repair

Charging Port Repair guide for the Motorola Moto Edge 50 Pro

Moderate
~44 min
21 steps

Before you begin

Tools

  • Heat gun or hairdryer
  • Suction cup
  • Plastic opening picks
  • Phillips #00 screwdriver
  • Spudger
  • Tweezers
  • SIM eject tool

Parts / materials

  • Moto Edge 50 Pro replacement charging port board
  • Pre-cut back cover adhesive tape
  • Isopropanol alcohol (99%)

Safety

  • Always disconnect the battery connector before handling internal sub-boards to prevent short circuits.
  • Do not puncture or bend the internal battery when working nearby with metal tools.
  • Wear eye protection when heating thermal adhesives near display glass.

Overview

# Motorola Moto Edge 50 Pro Charging Port Repair Repair Guide Action-specific charging port repair walkthrough for the Motorola Moto Edge 50 Pro. About 44 minutes across 21 steps. This DIY guide walks through charging port repair on the Motorola Moto Edge 50 Pro (Moto Edge series phone). Before you open the device, confirm the exact model number on the Motorola settings screen or rear housing so your replacement part matches the Moto Edge 50 Pro specifically—not a similar Moto Edge sibling. Most DIY techs finish this Motorola Moto Edge 50 Pro charging port repair in about 44 minutes when parts and tools are ready. Difficulty is rated intermediate for this model. Recommended tools for this Motorola Moto Edge 50 Pro job: Heat gun or hairdryer, Suction cup, Plastic opening picks, Phillips #00 screwdriver, Spudger, Tweezers, SIM eject tool. Parts and supplies: Moto Edge 50 Pro replacement charging port board, Pre-cut back cover adhesive tape, Isopropanol alcohol (99%). Power the Moto Edge 50 Pro off completely, remove SIMs/SD cards if present, and work on a clean, well-lit surface with a magnetic mat for screws. If a step feels wrong for your Motorola Moto Edge 50 Pro, stop and compare the connector layout to the photos in this guide. When you prefer a same-day pro repair in Seattle instead, LML Repair can handle charging port repair for this model with tested parts and a workmanship warranty.

Step-by-step

  1. 1

    Power Off and Eject SIM Tray

    2 min

    Turn off the Moto Edge 50 Pro completely. Insert a SIM eject pin into the SIM tray hole at the bottom to remove the card tray.

  2. 2

    Heat Rear Cover

    3 min

    Apply heat to the edges of the back panel using a heat gun set to 80°C for two to three minutes to soften the adhesive.

  3. 3

    Attach Suction Cup

    1 min

    Place a suction cup on the lower section of the heated rear cover and pull upward firmly to create a small gap.

  4. 4

    Insert Opening Pick

    2 min

    Insert a thin plastic opening pick into the gap created at the bottom edge between the frame and back cover.

  5. 5

    Slice Perimeter Adhesive

    4 min

    Slide the pick around all four edges of the device to cut through the factory adhesive tape. Reapply heat if the adhesive hardens.

  6. 6

    Remove Back Panel

    2 min

    Carefully lift the rear panel off the phone body and set it aside on a clean surface.

  7. 7

    Unscrew Lower Loudspeaker Assembly

    3 min

    Use a Phillips #00 screwdriver to remove the screws securing the lower speaker enclosure to the frame.

  8. 8

    Remove Loudspeaker Module

    2 min

    Gently insert a spudger under the loudspeaker module and lift it out of the phone body.

  9. 9

    Disconnect Battery Flex Cable

    1 min

    Pry up the battery press connector from the upper motherboard using a plastic spudger to cut power.

  10. 10

    Disconnect Interconnect Cable

    1 min

    Pop the main interconnect flex cable off its socket on the lower charging port daughterboard.

  11. 11

    Disconnect Antenna Cables

    2 min

    Use fine-tip tweezers to carefully unclip the white and black coaxial antenna cables from the daughterboard.

  12. 12

    Unscrew Charging Port Board

    2 min

    Remove the Phillips screws holding the charging port board to the lower chassis.

  13. 13

    Remove Damaged Charging Port Board

    1 min

    Pry under the edge of the charging port board with a spudger and remove it from the phone.

  14. 14

    Install Replacement Charging Board

    2 min

    Align the new charging port daughterboard into the recess and press it gently into place.

  15. 15

    Fasten Daughterboard Screws

    2 min

    Reinsert and tighten the Phillips screws securing the new board to the lower frame.

  16. 16

    Reconnect Antenna Cables

    2 min

    Align the coaxial antenna cable heads over their snap-on terminals and press down gently until they click into place.

  17. 17

    Attach Interconnect Cable

    1 min

    Press the main interconnect flex cable connector onto the daughterboard until it snaps secure.

  18. 18

    Reconnect Battery Cable

    1 min

    Press the battery flex cable connector firmly back onto the motherboard terminal.

  19. 19

    Reinstall Loudspeaker Assembly

    3 min

    Position the loudspeaker module over the lower assembly and secure it with its Phillips screws.

  20. 20

    Apply Back Panel Adhesive

    4 min

    Clean remaining adhesive off the frame edges with isopropyl alcohol and lay down new pre-cut adhesive tape.

  21. 21

    Seal Back Cover

    3 min

    Align the back cover over the frame and press down along the edges to seal the adhesive.

After your Motorola Moto Edge 50 Pro charging port repair

Power the Moto Edge 50 Pro back on and test the charging port repair function before you put every screw away. Check touch/display response, charging, cameras, buttons, and wireless as relevant to this repair. If something fails after closing the device, reopen carefully and reseat the connectors for this Motorola Moto Edge 50 Pro job before assuming the part is defective. Keep leftover adhesive and screws labeled in case you need a second pass.

Keep learning

Explore more Motorola Moto Edge 50 Pro repair context in the encyclopedia, or open related DIY guides.

logo_footer

Stay in the loop

Get new guides, reviews, and repair news.

© 2026 LML Repair. All rights reserved.